Haber akışı

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Robert
Inspiriert durch die aktuellen Anlässe in der Welt, meiner Liebe zum Leopard 1 und dem Wunsch ein Gebäude in 1:35 zu bauen, bin ich auf die Idee für dieses fiktive Diorama gekommen. Das Diorama soll eine Panzer Crew bei der Rast zeigen. Der Panzer ist ein Feldumbau eines beschädigten Leopard 1 der zum abfangen von Drohnen umgebaut wurde. Die Mannschaft nennt ihr Fahrzeug "Fliegenklatsche" (мухобойка).

Inspired by current events in the world, my love for the Leopard 1 and the desire to scratch build a building in 1:35, I came up with the idea for this fictional diorama. The diorama is supposed to show a tank crew taking a break. The tank is a field conversion of a damaged Leopard 1 that was converted to intercept drones. The team calls their vehicle a "fly swatter" (мухобойка).

Dieter Bihlmaier
Coole Idee...und super umgesetzt Robert !
Cool idea... and super implemented Robert !

Robert
Danke Dieter...

Robert
Die Mauerarbeiten sind fast fertig und das Dach ist vorbereitet...

bricklaying allmost done & roof prepared...

Robert
Die Mauerarbeiten sind abgeschlossen, das Modell ist schwarz grundiert und die Backsteine sind bemalt...

The masonry work is completed, the model is primed black and the bricks are painted...

Spanjaard
great idea. i love how the house is evolving

Robert
Thanks Spanjaard

Robert
Die Ziegel wurden verfugt und das Dach aufgesetzt. Die Dachrinne wurde aus einer Katzenfutterverpackung (Aluminium) und das Fallrohr aus Gussgraten hergestellt.

The bricks were grouted and the roof was added. The gutter was made from cat food packaging (aluminum) and the downpipe was made from plastic sprue.

Robert Podkoński
Great concept indeed! Fantastic job so far, Robert. Keep it up!

Robert
Thanks Robert...

Robert
Dioramarahmen vorbereitet, Straße und Gehweg angelegt. Den Kamin verfugt und die Figuren zusammen gesetzt.

Diorama frame prepared, street and sidewalk laid out. The chimney was grouted and the figures were put together.

Jennifer Franklin
I love it all. The house is incredible. This looks like it is going to be a diorama with personality!

Robert
to kind, Jennifer

Jennifer Franklin
No, honestly, it is brilliant; I can't wait to see the final result.

Robert
I'm also curious what the end result will look like..
😀

Robert
Garagentor erstellt, bemalt und installiert. Figuren grundiert. Strasse und Gehweg vorbereitet.

Garage door created, painted and installed. Figures primed. Road and sidewalk prepared.

Guy Rump
Definitely following. 👍

Recce 4-6
Wieder mal ne coole Idee und handwerklich sehr gut umgesetzt.

Robert
danke Recce 4-6

Jennifer Franklin
That garage door looks good.

Robert
Thanks Jen

Robert
Fenster und Gardinen eingesetzt, Straßenmarkierung aufgemalt und Gehweg verfugt...

Windows and curtains installed, street markings painted and sidewalk grouted...

Rui S
Great scratch build on those Buildings 👍

Robert
thanks Rui...

Robert
Haustür eingebaut und Regenrinne und Fallrohr vorbereitet. Die Regenrinne hat mich mehr Zeit gekostet als vermutet.

Front door installed and rain gutter and downpipe prepared. The gutter took me more time than expected.

Dieter Bihlmaier
Schaut sehr gut aus Robert!

Robert
Danke Dieter...

Mr James
One of my favourites ww2 aircraft. A nice clean build

Skyhiker
Dave really nice job. Which kit is this? Please attach the kit to the project.

SlaveOfDystopianEducation
On a rainy and humid day, Jack was depending his life or death on a tiny landing craft on the ocean making its way to the enemy's shore. The thunders and the strong waves made him and other soldiers cramped in the narrow space anxious and nauseous. What if the vehicle just gets flipped by the waves? What if it gets spotted by the enemies while they're on water and can't run to anywhere? Jack could tell his fellow comrades were feeling this way by looking at their eyes. But not Jack. He was somebody who never let fear control his action and psychology. His pupils were filled with combinations of energy, rage and hatred instead of horror. Losing his closest buddy to the enemy aircraft bombing in the past, Jack was totally committed to kill as many enemies as possible to avenge. It would be so awesome to make many enemies feel the pain he had to endure with his own hands. At least that's what Jack believed. The shore was now visible. They were almost there. A few bullets from the machine guns hit the metal surface of the vehicle, making loud and sharp noise. Some soldiers fear and Jack's rage only grew.

Jack was ready to fight. He even thought he was ready to die. He was looking directly forward when he heard some noise that was completely unfamiliar. It wasn't the sound from bullets, explosions or engines running. It was something else. The only thing he could tell was that whatever the source is, it was coming from the sky which meant only one thing. Jack tried to ignore the fear which was now settling in his mind and keep looking at the shore. But eventually looked up the sky expecting the sound's source to be friendly artillery or aircrafts. Little did he know he couldn't be more wrong than this. They were Stukas. And they were flying towards the friendly boats.

At the moment Jack found out what they were and that they are coming for him and everyone else, his passionate strength in his eyes started turning into immense shock and awe even he couldn't control just like other soldiers. He had to realize that him and everyone on the craft were now gonna die even before making it to the shore. Sure, he was ready to die but not without killing others. However, the reality was way too harsh to let Jack achieve what he wanted in the war.

Sure enough, everyone heard the loudest gunshot coming from the aircrafts. The Stukas had begun firing. It hit the other boats around before hitting his. Even from dozens of feet away Jack could see the sparkling on the iron and the huge splatters of blood followed by his comrades screaming in agony. Now it was his turn. He stared at the planes looking for more targets then spotting the boat he was in. Tears started coming out of the despair about the fact that this was the end of him just like his buddy and thousands of his country's soldiers who didn't make it. So he didn't even try to hide or stop it. Instead he closed his eyes, hoping there is going to be something better to have in the afterlife if it ever existed.

Dave
Wow, that's a true description of how it must've felt being on the receiving end of that aircraft and its mission

Dave
Skyhiker, I'm sorry I didn't list the kit. But it is 2002 Academy 1/72 scale kit

J35J
Great build! Congrats👍🏻

Skyhiker
That kit looks a lot better than the old Revell kits I have. Can you please attach it to your album.

Guy Rump
Very nice job! 👍

Dave Flitton
Nice build.

Rando
VF-161 might just be my favorite Phantom scheme, so the box art sold me on this one. I need to enjoy a state-of-the-art kit and I hear Fine Molds is excellent. I got some masks and missiles on order but otherwise just a nice simple OOB here.

Rando
This kit is awesome. I'm already on to the main fuselage assembly and I'm not even rushing—it just falls together. Instructions say to paint (and decal?) after the fuselage and wings are attached

DerMattes
Watching 👍

Tommy Agne
Count me in! Watching👍!

Dave Flitton
Nice start, count me in.

Jan Peters
Very nice work!
I love models created after a photograph.
You have made quite an effort creating this one 👍🏻👍🏻

Erwin Leetink
Revell's 1:32 Arado sea plane. In the guise of one of the planes aboard the Tirpitz. The instructions call out for a (nice) decal that indicate the 100th launch, but since I found pictures that the plane had them on both sides, and only one is included, I left it off.
I added the national markings on the tail and replaced the lifting /handling cables for metal ones. Since I am not sure what color those cables where, but doubt they would be painted (the paint would flake off due to the flexing of the cables) I left them metal colored.
The dust somehow got embedded in the matt varnish, even though I painted the plane outside and let it dry there too!!!

Dave Flitton
I think you pretty much nailed the result. It looks very nice.

Rui S
Beautifully done 👍

Randy Kriegel
Thank You

Agrippa
great work!

Neuling
Very appealing small scale build!

Dave Flitton
I saw a video review on this one. How was your build?

BetterTimes-Henry
Very nice👌

Randy Kriegel
This UM build was difficult, lots of nice details. I had a little trouble with the instructions, but worked through it. Overall it's a good kit.

Agrippa
What happened to the instructions? I still have the kit here.

Dave Flitton
Excellent result!!

Frank Brzobohaty
NAXOS receiver done and front engine too.

Dave Flitton
Nice start!!

Shar Dipree
Following

Finn
I'm in

Łukasz Gliński
Joining, looking very 48ish

Frank Brzobohaty
Thank you.

Frank Brzobohaty
Base painting done. I need to learn to do the continuous line camo for the next night fighter. Any good guides for 1/72 scale? I am good enough to do it at 1/48 but just not skilled for 1/72.

Rui S
Beautiful work 👍

Dave Flitton
Excellent result. Makes me excited to build mine, if I can find it.

Skyhiker
My next big project is turning this FROG into a Prince. Wish me luck I'm going to need it.

Moreno Baruffini
Good luck! 👍

Robert Podkoński
Ambitious! Keep my fingers crossed!

Nicolas
I'm following. In my opinion the Ta-152H is the most beautiful plane of WW II. I got the kit from Kora in my stash and hope to start the build in spring this year. Good luck and, above all, have fun building it.

Skyhiker
Nicolas, I agree. It's a long, lean, fighting machine as they say. Definitely one of the more elegant designs to come out of the war.

DerMattes
Taking a seat 🙂

Skyhiker
I had to widen the fuselage today, in order to make space, before I scratch build the cockpit.

Jennifer Franklin
Following 👀

Skyhiker
Bit more done today.

Lukas Muller
good job 🙂 Following

Łukasz Gliński
Respect for your patience 👍

Martin Nevo
this is going to be awsome.
I am picking kits that are near perfect so I have fun.
but there are also people who pick not-so-perfect-kits like this Ta152 and they still have loads of fun!
GL 🙂

Skyhiker
Well mostly I pick not-so-perfect-kits because I'm a cheap skate. I'd rather pay 6 euros than 40 for a kit. I do have some moderately priced kits and they are a lot faster and fun to make, but often I just have the need to challenge myself and see where my skill level is at.

Rui
This looks like a real challenge; I'm watching 🙂

Moreno Baruffini
@Skyhiker: I totally like your approach and I think you did a great start!

Martin Nevo
same here @Skyhiker, I really like the 6eur price point. so affordable. probably thats why I started to look into the 1/144 scale 🙂

Skyhiker
A bit more progress on the scratch built cockpit today.

Jennifer Franklin
Excellent work on the exhausts, and the cockpit is coming along nicely.

Skyhiker
I did a bit more today but I can't seem to get any images to upload. Anyone else having these problems?

Treehugger
Looking at photo #17 I want to give a tip:
I would be a little careful keeping the roll of masking tape on the table. I like keeping them in a holder, or placed in a bag, to avoid the side of the roll picking up all kind of dirt.

Skyhiker
Yes, I keep my tapes in a bag but it doesn't seem to help as well as it should. I think I need a better bag. When I photograph things at this scale there is more dust than I realize.

Jennifer Franklin
I can finally upload my images again now, I was having problems too.

Skyhiker
Thanks Jennifer

Skyhiker
Treehugger I cleaned my tape and got a new bag. Thanks for pointing that out. No need for fuzzy tape.

Skyhiker
Cowling remade with a lot of sanding, cutting new flaps and a PE grill.

Moreno Baruffini
Really a great progress!

Skyhiker
Thanks Moreno, I am having fun with this one.

Skyhiker
I have to take a break and will be back in a week. I must say I am in love with this plane. It's really a beautiful design with those long wings. I can't wait to get back to it.

Lukas Muller
I'm agree with you, one of the most beautiful plane for me 👍

Dave Flitton
I like it so far!

Guy Rump
I'm going to build this one from my stash this year, definitely following! 👍

Skyhiker
The canopy was totally uneven and so I decided to do the risky thing and file it from the inside. Hopefully I didn't just ruin it.

Vincent
This is already an impressive build. Good luck!!!

Skyhiker
Worked a bit on the cockpit today.

Oliver
Follow. Want to See the result

Skyhiker
This kit has its flaws but nothing that can't be corrected with a little bit of skill. Are there more accurate kits out there that are easier to build - yes. But the modern trend of wanting perfect kits seems counter to the art of modeling. If you have ever built a model from a block of wood you wouldn't call this kit useless. Challenging or time consuming I can agree with but it is not crap.

Skyhiker
I haven't given up yet. Sometimes life forces me to take breaks but I hope to get back into this one soon. I have to put a lot of tiny details in the cockpit next and I need the right head space for that. Kits like these take time and often I will start easier kits mid process to keep things flowing. I absolutely agree that reboxing old kits without a mold date is deceptive. Thankfully with this site we can look up the history and sometimes see the sprues before buying anything. I've only had one kit that I couldn't do anything with. I bought it for 20 bucks opened up and threw it directly in the trash. That was a Top Gun F/A-18 Hornet snap kit, which really was a piece of shit.

Remco van Haren
Following. Really looking forward to the end result.
Especially since I built this kit myself last year. Although I didn't put so much effort and detail into it as you are doing.

Johne 69
So gar so good 👍

Skyhiker
I added a bit of detail to the scratch built cockpit today.

Skyhiker
Worked on the canopy and tried to figure out how the scratch built cockpit will fit into the body.

Skyhiker
I corrected the seat position today.

Skyhiker
Added some space for the wheels

Skyhiker
Trez your message is pretty cryptic. Are you talking about panel lines or internal wing structures? The last photo is just a dry fit. I haven't started with dealing with any panel lines yet. I've been working on the inside of the wing walls to make something that gives an impression of space for the wheels.

Skyhiker
Trez, thanks for your ideas. I'm using a lot of photos and the instructions from a 1:32 model to help figure out what is going on. This little model is a challenge to correct but I'm having fun pushing my skills and learning as I go.

Moreno Baruffini
I'm really enjoying this build! 👍👍👍

Skyhiker
I worked out most of the cockpit issues today. It's not perfect but I got it in there.

Skyhiker
Moreno, I'm glad you're liking it. This is kinda pushing my skills a bit. We'll see what happens in the end together.

Skyhiker
Getting this kit to accept a cockpit was like pounding a square peg through a round hole. I had to reshape the whole damn fuselage.

Patrick Hagelstein
Whoah!!! Amazing what you did to that old tooling! Very cool to watch! 👍🏼

Skyhiker
Thank you Patrick. I'm trying. We will see if it works.

Bruce Huxtable
Really liking what you're doing, Skyhiker, and learning lots too. Impressed with your skills 🙂

Łukasz Gliński
What is that superglue thingy?

Skyhiker
Łukasz the shape of the hood is really off in the kit. The superglue is just material for me to try and sculpt into a better hood.

Łukasz Gliński
I was just wondering if you have mixed it with something

Skyhiker
No, It's just cheap super glue from a discount store that I poured right from the tube and hardened with accelerator.

Skyhiker
Started reshaping the fuselage today.

Skyhiker
Hood work today.

Nicolas
That looks very messy. But as long as it works, and it looks promising.

Skyhiker
Yes, very messy but it works. Old school style.

Patrick Hagelstein
The effort put into this is just amazing! 👌🏼

Skyhiker
More work on the exhausts today.

Moreno Baruffini
The true essence of modelling!

Skyhiker
I began rescribing the panel lines today. This will take a bit of time.

Tony Cooke
Dedication!!

Skyhiker
Bruce, thanks for your encouragement. It definitely helps.

Dave Flitton
That's a lot of work!

Skyhiker
Well the fine engraving blade I just bought broke within a day of use. Very frustrating.

Skyhiker
Luckily I bought a .02 mm blade in addition to the .01 mm that broke. It will have to do even though I would prefer the lines to be a little bit thinner.

Skyhiker
I finished the panel lines on the underside of the wings today.

Vincent
Impressive work!! Keep it up!

Patrick Hagelstein
Amazing progress! Once you go the route of updating such an old kit, there's no way back, is there?

Skyhiker
Thanks Patrick, your right there is always more to discover and do. I'm having fun with it. Of course I have no idea what it will look like in the end. I'm spending far too many hours allowing myself to be lost in process. But if that's what it takes, why not?

Skyhiker
It's amazing how every kit I look at of a FW Ta 152 H is different. All the photos of the original aircraft are so blurry that details are impossible to pick out, so I'm left with looking at kits and guessing which ones are correct.

Skyhiker
Anyone out there with a book on the TA 152? I'm trying to figure out if the top of the flaps have a vertical line down the center of them or not. From underneath there is a line there but I am getting conflicting images of the top surface. Can anyone post a decent image?

DerMattes
I looked through some of my books and picture collection. But to find even a picture of the Ta152 is rare. 🙁

Skyhiker
Thanks Mattes. There are a few decent books out there but they go for 80 Euros and I can't afford that. I doubt the library would have anything worth while. Maybe the model shop will let me look through one of their books but usually they are sealed in foil. Hopefully someone here has something. Getting panel lines correct is not so easy. Even worse are the rivets.

Skyhiker
I found this image which clearly shows the flaps divide in two sections. Interestingly the sections are not even like the underside.
[img1]

DerMattes
Maybe this would be helpful? flugzeugclassic.de/f..hlands-bester-jaeger
I do not have the magazine, but kind of stumbled over the link 😉

Skyhiker
That's cool Mattes. Thanks for the tip.

Ben M
I admire you trying to make something of this kit.

Skyhiker
Thanks Ben, this kit gets a bad rap. It's not as bad as people make it out to be. Of course I am putting a lot of work into it to make it better. But if its done straight out of the box it's not that bad. The backwards propeller is a stupid engineering mistake but that's an easy fix.

AndreasK
Nice project, Skyhiker. And really stunning what you achieved so far. 👍🏻

Sy Bar
Can't wait to see fruits of your hard work 🍿

Skyhiker
I'm worked on the top side of the wings today.

Skyhiker
Panel lines... panel lines and more panel lines...

Matthew A
Owch

Skyhiker
Yeah, I was a little heavy handed, but it's not a problem. I just glued it back together. I prefer trenching and filling over trying to get the lines the exact depth overall and then accidentally sanding away lines. The only problem with using this method is the deep panel lines can make the model unstable in places if you are not careful. But in the end it should all work out.

Skyhiker
I am slowly moving forward on the panel lines behind the scenes. This is the part I have to force my way through because I don't really enjoy it. But it is coming along and I could have some photos soon.

Patrick Hagelstein
Looking forward to that! 😊

J35J
Good progress, great craftmanship!👍🏻

Skyhiker
Got most of the panel lines down. I still have to do the bottom.

Moreno Baruffini
I personally ate re-scribing, so my admiration for you is huge!

Skyhiker
Thank you Moreno, re-scribing is definitely the part that's the least fun for me too. Some days I have to force myself just to do one line. If you do that once a day eventually it gets done. But yeah, re-scribing sucks.

Skyhiker
Big step made with attaching the wings. It makes me feel like I am moving forward after all.

Patrick Hagelstein
There ya go! 😄

Skyhiker
Wing plates are made.

Pietro De Angelis
An impressive amount of work, your patience and skills are incredible, congrats!

Skyhiker
Thank you Pietro.

Thomas Kolb
Wow, what an insane amount of work you put into this project! I am humbled by your perseverance and attention to detail!

Skyhiker
Thanks Thomas, I enjoy the process of trying to figure out how to do stuff. The model is just an added bonus in the end.

Skyhiker
Today I continued with the landing gear. A few pictures added.

Moreno Baruffini
As I wrote above, it's the true essence of modelling!

Skyhiker
Thanks Moreno. I'm having fun with it, mostly. The panel lines were a drag but I got through that part. Hopefully after the primer I won't have to any major touch ups. But we will see. One step at a time...

Skyhiker
Primer started!

Johne 69
Nice Details 👍

Skyhiker
Yesterday and today I filled the panel lines to the appropriate depth.

Patrick Hagelstein
This keeps on being cool to watch! 👍🏼

Vincent
Watching you making process is indeed great to watch. The plane is starting to look great!

Moreno Baruffini
Wow! How do you filled the lines? How was you able to calculate the exact quantity?

Skyhiker
Moreno, I used an engraving tool to cut deep lines and then I rubbed white putty into them. By rubbing the excess off it automatically brings the lines to just below the surface of the model. As the lines dry they also shrink a bit. So, it was not too hard to do. The trick is to use enough water and a brush to apply the putty and to use enough water on a paper towel or cotton bud to remove the excess. Hard to get to areas need to be cleaned up with a wooden tooth pick.

Robert Podkoński
I never would believe that the base kit is a Revell's offering.... Awesome job!

Moreno Baruffini
@Skyhiker: Super! Many thanks for the explanation!

Alec K
Great project and some serious dedication to a challenging tooling 👍

Skyhiker
I worked on some details today. Tomorrow I will give it another coat of primer and hopefully start the riveting.

S M
Wow this is borderline masochistic👍

Skyhiker
I am debating with myself when the best time to do riveting is. If you do it before priming you run the risk of filling the holes. If you do it after priming it makes it harder to correct mistakes. If you do it after the final paint job you run the risk of fucking everything up. Anyone have any experience with riveting?

Matthew A
I think you typed f when you should have typed m

Skyhiker
I stand corrected. Thanks.

Alec K
Regarding riveting: I have done it before priming but I don't see why you could not do it after. You'l have to sand after as the riveter leaves 'rings' around each divot (as it pushes the plastic out). In my experience, a thin coat of primer has negligible impact on the rivet holes (if it had, this would be a problem with any factory-riveted kit).

Skyhiker
Alec, I tend to agree with you. My thoughts on doing the riveting after the primer was that the rivets may remain a bit better defined. But I am not convinced. I think I will have to do some tests for the future. By riveting before and after the primer on some styrene, then spraying a color coat over both should give me a better idea of which I prefer. Right now I feel like I prefer not doing it at all, because riveting is a pain. But that's just me feeling sorry for myself for wanting to do a half way decent job on this kit. I do wish I could find some reliable riveting guides for this plane. It seems like everyone is just guessing at it.

Skyhiker
I got some riveting done today.

Patrick Hagelstein
That riveting looks very impressive! 👌🏼

Skyhiker
Thanks Patrick, I haven't mastered riveting or panel lines yet but I'm learning. I am pretty limited in my tools and the scale is not the easiest. But with practice and study I hope to improve.

Skyhiker
I've realized that one of the benefits of doing the riveting after the primer is that you can make sure that most of the sanding is completed. However inevitably there are areas that get messed up and sanding is required after all. I just haven't found the perfect solution.

Sy Bar
Enjoying your progress a lot, the transformat is amazing.
I must say your plans are so clear and great reference where do you get your plans like these from, I search the tinternet but never find any as useful as your plans, any extra guidance would be appreciated

Skyhiker
I drew my plans on the computer by looking at various images on the internet. Unfortunately I haven't found any place to download great paneling or riveting guides. There is a Russian website that has blueprints that I sometimes use but I'm not sure if it is still available. I didn't use it for this project.

Skyhiker
Sy Bar, which plane will you be doing next? I can look around for blueprints and see if I can find anything useful.

Sy Bar
Cheers Skyhiker v kind offer and thanks for the info. Not sure what will be next and if plans will be required but I'll keep you in mind should the need arise.
Keep up the work I'm loving watching the progress 👍

Skyhiker
Widened the wing roots and I am continuing with the riveting today. Also I did a lot of research on the proper colors to use, which was not as easy as one would think. They certainly are not what the instructions say.

Moreno Baruffini
Great work as usual! I'm curious about the colours: aren't they the late RLMs?

Skyhiker
The colors are late RLM colors but not exactly as the instructions say. To start with they call for the hood to be RLM83 which of course is wrong, since in actuality that was a marine color and blue. Many paint manufacturers have some type of green with that number but it was based on a typing mistake in the original RLM records. I believe the hood should be RLM73 as in the original photos it is a bit darker than 81. The fuselage is RLM81 and RLM82, but there were three variants of 81, two that were brownish and one more green. The green is the correct one for this plane. The under carriage is RLM76, but once again we have three variants to choose from; one that is greyer, one bluer and one more tan colored. The greyer one is correct. There is confusion about whether the nose is red or black. I still have to do more research on this. I believe the propeller blade was RLM70

Moreno Baruffini
Many thanks! Super explanation! 😀

Skyhiker
I hope to be finished with the riveting today. Most of my time was spent trying to figure out which of the conflicting diagrams was closest to the original. I don't know if I got it right since there are no surviving planes left.

Oleksii
Great Work on this old Revell Kit and there is still one surviving aircraft.In National Air and Space museum.
airandspace.si.edu/c..11/nasm_A19600317000

Skyhiker
National Air and Space museum has a different version of this plane. It is very similar but there are a lot of differences.

Oleksii
Ouh okay, thank you

Skyhiker
Worked on a bunch of details today.

Skyhiker
I redid the engine today and laid down a second layer of primer. The rivet lines came out well. There are just a few small touch ups on the engine cover and wing tips to do before I start on the wings.

DerMattes
Fantastic work, looks like a different kit!

Skyhiker
Thanks DerMattes. It's more a scratch build than a kit at this point. It's starting to come together. I still have a while to go though. How is a scratch build defined at the official contests?

Hans-Jürgen Haag
From an old crow to an up to date beauty! Owsom project!👍👍👍

J35J
It's like you are building a vac kit with the amount of work and attention to details you are putting into this build. Impressive and inspiring!👍🏻

Skyhiker
I made a gunsight out of 7 scratch built parts that is only one millimeter in size.

Nicolas
The gunsight looks fantastic.

Alec K
Indeed, looks awesome 👍

Skyhiker
Next I have to try and repair or replace the front windshield. Somehow it cracked when I was sanding it down. Is it me or do the clear parts on Revell kits always have problems?

Skyhiker
Well I painted the propeller today but afterwards I had to clean my Iwata airbrush and change the needle. Unfortunately the needle noozle broke off in my airbrush and there is no way to fix it! Now I have to rely on a cheap Chinese knock off to finish painting until I can save an extra 150 bucks to buy a new airbrush.

Nicolas
That sucks. I'd love to lend you my second airbrush, but unfortunately that's also just an old Chinese product at the moment. Probably wouldn't help much.

Nicolas
What now? Aftermarket or scratchbuild canopy?

Skyhiker
I will try scratch building the canopy if that doesn't work I will have to get a vacuform machine.

Duster_d
I wish I could add another like for your vacuum machine! Man, you're really cool!

Ben M
Never give up.

Skyhiker
And the results are in.

Ben M
Did you follow a tutorial? Very interested in how you did this

Skyhiker
No, I just needed to make a canopy so I first tried replacing the front windshield with a clear plastic piece from a CD cover and glueing the original side windows to it but when I finished it was too thick. So then I made the front windshield out of thin plastic sheet from some packaging I had laying around. That worked but the bubble canopy was now too thick. So I tried making a bubble canopy by heating up some of the plastic sheet over a candle and pressing it down over the original with my fingers but that didn't really work. I only got one that looked right but I burnt it so I realized I needed to use a vacuum and change my heat source. My hair dryer runs so hot it overheats and turns off, so I tried that with the vacuum and it worked. You just need to tape the plastic on a piece of cardboard with a hole cut into it and practice. You can make the vacuum screen out of anything. I just used an old sanding disc that I punched holes into and taped down on my sweeper.

Ben M
I'm not sure I can visualize that yet but I'll see if there's something on YouTube. I have a truck I need to make a windshield for.

Mr D
🤣🤣 love the vacform 😁, l split the canopy on my little mig-23 project, to heavy with the Quetip/ ear cleaner!!
I used toaster n paintbrush end 🤣, it worked...but was just a little 1/144 mig-23, it's my wall.
The homebrew job was clearer than the original 🙄,
Would love a little vacform.
Love the scale detail you go to.
👍👍👍

Skyhiker
Ben here is an example I found on YouTube of vacuforming. youtube.com/shorts/GFSJxs51uoY?feature=shared

Ben M
Thank you!

Jennifer Franklin
I will have to bookmark that reference, love it Skyhiker!

Skyhiker
Just make sure that the plastic you are heating up is polystyrene and not PVC. You don't want to poison yourself with heavy chemicals. Polystyrene is bad enough. And don't use your oven or anything that will be in contact with food.

Skyhiker
I made another canopy. This time as one piece. After painting I will try to separate it.

Mr D
That canopy has come out nice n clear.👌
I think it would be nice model with closed canopy also.
I like closed as keeps the dust out n preservation on cockpit.... Little time capsule too.
Doing a good job, persistence is a good trait in this hobby 🙄😆.
I've spent more time making a missing gun turret.! Than on the rest of the build !!

Skyhiker
Working on the landing gear today.

DerMattes
You mean you build an entirely new landing gear, right? At least this is how it looks 😉 Impressive work and dedication!

George D Munro
Cannot wait to see more. Amazed at the effort expended to correct, such an old kit. Reminds me of a favorite saying of a long lost friend. "that wouldn't stop a good modeler". A good modeler you are. I thought Inwas pretty good, but am in awe of your talent and dedication. Am following

Mr D
An amazing amount of improvement and scratch work to improve the model.
Very impressive..👍👍

Skyhiker
Thanks guys. I'm trying. Learning a lot on this model. It certainly is a challenge, but I'm having fun.

Skyhiker
So, the legs are on now.

Mr D
Can l ask what the 🕯️ candle wax was for?? I was guessing 🤔 maybe to build up higher for super glue. ? I like watching builds as you can learn new skills.
Also if you don't mind, how did you thin down the retract arms ...looked machine down.
Enjoyed watching so far being fascinating,
I built the Revell FW-190 this year ...that wasn't to bad.... Few of the engine fan blades hadn't been moulded in !! So l built them back with super glue gell, back wheel was fragile n came off. But rest ok .
Thanks 👍👍

Skyhiker
Mr D. The candle is used as a receptacle for the super glue. It helps to keep the super glue from setting. By putting it on wax and covering it with foil it will remain in a liquid form for a whole day. The retractable arms were made from styrene rod and stretched sprue. The thick end is the rod. The thin end is sprue and the raised area is very thin sprue wrapped around it.

Mr D
Thanks for the info 👍👍.
Have you tried super glue gel?? It's slow to dry but builds up more.well.

Skyhiker
No, I haven't had a need for that. I just use cheap super glue. 5 tubes for a Euro.

Skyhiker
I gave the wings a boost.

Robert Podkoński
WOW. I admire your perseverance!

Mauricio
Impressive work, I am currently working on a similar kit, I didn't know whether to repanel, but I don't think I have reached that level that you achieve... excellent, I will follow your work closely!!!

Skyhiker
Welcome Mauricio

Skyhiker
Starting to paint a bit now.

Greg Baker
I've got one of these in the stash and every time I look at it I go "nahhh..." and grab something else to work on. This project has given me hope that something good can be done with that kit. Nice work!

Skyhiker
Thanks Greg. With enough attention it can be pretty decent. I guess it just depends on how much time you want to invest. Certainly there are better and easier kits on the market. But I enjoy reworking old kits every once in a while to push my skills. Just painting perfectly molded kits somehow doesn't seem like modeling to me.

Kesa Tiho
Very nice finish so far, following with interest

Skyhiker
Well I broke both retractable arms from the landing gear today. Tomorrow I will have to come up with a better solution. Luckily I just got a shipment of brass tubing that just might work.

Mr D
@Skyhiker
It can be one step forward n two back sometimes!!
I've had few instances this week...paint to re-do and now bit of glue gone on my tire!
Good luck with brass tube🤞.
Can't be as bad as a snapped canopy 🙄....keep going 🤣

Skyhiker
I think this back and forth that I experience with every model is just the plight of being an intermediate model maker. I hope to one day have enough experience that things go easy but maybe that's just wishful thinking.

Mr D
That brass tube is better job around 👌. nice n strong.
Wouldn't mind some myself?? 🤣
Every day's a school day..🤣 always learning hopefully, you must be doing something right as you have alot of interest in the project.. Enjoying the process is most important part.

Skyhiker
So, today when I woke up I realized that there was a problem with the horizontal stabilizers. So I had to take them off and rebuild them. If course that lead me to seeing more areas that needed sanding. In the process of sanding I knocked off the wing tips and canopy. Glued them back on. Polished things up and tomorrow I will give it another spray of polished aluminum.

Mr D
Hi Skyhiker 😃👍
Chin up...and move on, .... These are the times when we say "l just want to get this built now" 🤣
I nearly messed up my current IAR-80 build from the first step's .... assembled the cockpit floor upside down!! Assuming and not double visual checking! Could have screamed 😲. Anyway....l cut X3 levers n rudder pedals off n glued on right side ... Just about recovered it.
I didn't think the VS's looked to far off ?? The 190 had bit of dihedral... But not the 152.
Do you use PVA on canopy ??
Good luck on next steps..... Getting near finish line now😁👍👍

Skyhiker
I am using Glue n Glaze (a type of PVA) on the canopy because I will need to remove it later and cut it apart to have an open canopy.

Skyhiker
I laid some color down today.

Mr D
The intake looks really good now 👌

Skyhiker
Thanks Mr D. I added a bit of dry brushing and will start with the main color tomorrow.

Skyhiker
It not easy being green.

Mr D
🤣
Doing ok👍 nice when a bit of colour starts going on.
I'm at painting stage on my project.
Does this one have any mottling? Like on the 190 ??

Skyhiker
I got the camo laid down.

Mr D
That answer my question? 🤣
That's come out good, nice balance 👍👍 it's easy to over do it .
Looking good 👌

Dave Flitton
Them paint is looking very nice!