Renault
Yorumlar
31 December 2012, 09:08
![](/profiles/img/10232-810-s.jpg)
Hey Fethi, its looking cool! Do you always place the windows after the paintjob?
15 January 2013, 09:16
![](/profiles/img/12420-662-s.jpg)
Hi Holger, thank you so much 🙂 only for this model i preferred to install the windows later. Normally i am builging the cab from inside to outside and painting at the end.
15 January 2013, 09:44
![](/profiles/img/10923-723-s.jpg)
Looks great Fethi, nice paintjob, great result so far😉
Greetz Phil
15 January 2013, 12:16
![](/profiles/img/12420-662-s.jpg)
@Holger, actually it is better because after installation the windows, masking procedure is a little difficult and sometimes the paint may come toward to windows even well protected.
16 January 2013, 07:36
![](/profiles/img/10232-810-s.jpg)
I´m looking forward to see the result of your craftmanship, Fethi!😢
16 January 2013, 09:16
![](/profiles/img/12420-662-s.jpg)
I started to pain the body. Unfortunately the model was very old and the decals are not fixing to body. I think there is no any solution for this, even i put them into water many times, they are not staying in surface.
17 January 2013, 07:30
![](/profiles/img/11566-604-s.jpg)
Did you use any decal solution like from Daco or Microsol and Set?
17 January 2013, 07:33
![](/profiles/img/12420-662-s.jpg)
Hi Michel, no i did not use, but the dacal lost their adhesive function. Will it work if i will use a microsol?
17 January 2013, 12:42
![](/profiles/img/11566-604-s.jpg)
Normaly it should. But if other modelers have experience with that let's come forward. 🙂
17 January 2013, 13:01
![](/profiles/img/10232-810-s.jpg)
I use the Revell decalsoft and can work with that on old decals. In case they are too old i use the liquid decalfilm from Microscale. That stuff rocks!
17 January 2013, 13:05
![](/profiles/img/12420-662-s.jpg)
Thank you too much for sharing your experience with me. I will try it. 🙂
17 January 2013, 15:09
![](/profiles/img/12420-662-s.jpg)
Dear Holger, should i apply the solution under the decal or above the decal?
17 January 2013, 15:10
![](/profiles/img/11462-s.jpg)
put it over the decal once in place,dont worry if it wrinkles this is normal,and should settle down while it is drying
17 January 2013, 15:26
![](/profiles/img/10232-810-s.jpg)
Hi Fethi, it works the following way:
At first you apply the liquid decalfilm on the decals you wanna work with (Just with a brush. You are allowed to use more than a bit!). After letting it dry for 12 hours you cut them out and do the normal work on them. But its important that you first apply the stuff and then cut them out. If you do it vice versa, the decals would stick to the sheet and you have no possibility to recover them! Hope that helps!
17 January 2013, 15:27
![](/profiles/img/10232-810-s.jpg)
And do yourself a favor and get yourself some stuff like "Decalsoft" or "Microsol and Set"! You will be amazed how wonderful your decals will creep in any detail of the surface of your model!
17 January 2013, 15:30
![](/profiles/img/10232-810-s.jpg)
Important!
My first description is how to use the liquid decal stuff to recover old or torn decals, not the description how to use decalsolutions to set decals perfectly!
Not that you get confused, Fethi😢!
17 January 2013, 15:38
![](/profiles/img/12420-662-s.jpg)
Dear Holger thank you so much, 🙂 🙂 first i will buy decalfilm from Microscale and will try it. I tried with Revell decal soft but they are not fixing to the surace.
everyday i am learning something new
17 January 2013, 15:41
![](/profiles/img/10232-810-s.jpg)
No problem, Fethi! You are welcome!🙂
Cheers Ole, good that you mentioned that the wrinkling of decals is not a problem when working with decalsolution!
17 January 2013, 15:53
![](/profiles/img/12420-662-s.jpg)
Hi Holger, i applied the decalfilm and works very well. Thanks again 🙂
28 January 2013, 11:48
![](/profiles/img/10232-810-s.jpg)
Good to hear! So you can head on now! I´m eager to see the result!8)
28 January 2013, 12:21