Grumman F7F-3 Tigercat (Monogram)
![Album image #1 Album image #1](/albums/img/9/3/3/47933-10105-75-720.jpg)
The raw materials...
![Album image #2 Album image #2](/albums/img/5/7/5/48575-10105-50-720.jpg)
Seat belts glued to the seat.
![Album image #3 Album image #3](/albums/img/5/7/6/48576-10105-37-720.jpg)
Engine block and crankcase - yes there is a spline on the propeller shaft.
![Album image #4 Album image #4](/albums/img/5/7/7/48577-10105-90-720.jpg)
Re-scribed fuselage on the right - plus a few boo-boos filled in with putty.
![Album image #5 Album image #5](/albums/img/5/7/8/48578-10105-74-720.jpg)
Black wash brings out the detail on the cylinder head cooling fins.
![Album image #6 Album image #6](/albums/img/5/7/9/48579-10105-12-720.jpg)
Just to give you an idea of how small these little buggers are!
![Album image #7 Album image #7](/albums/img/2/9/8/49298-10105-62-720.jpg)
Cockpit raw materials - Gunze H58 Interior Green with some shadowing and highlighting.
![Album image #8 Album image #8](/albums/img/2/9/9/49299-10105-25-720.jpg)
Port console.
![Album image #9 Album image #9](/albums/img/3/0/0/49300-10105-53-720.jpg)
Seat and belts.
![Album image #10 Album image #10](/albums/img/3/0/1/49301-10105-12-720.jpg)
Starboard sidewall. Have no idea what all that stuff is, but I painted it anyway.
![Album image #11 Album image #11](/albums/img/3/0/2/49302-10105-64-720.jpg)
Major nacelle surgery.
![Album image #12 Album image #12](/albums/img/3/0/3/49303-10105-27-720.jpg)
I had to shorten the PE wheel well ceiling by a lot for it to fit. Not too keen on this part of the Aires set.
![Album image #13 Album image #13](/albums/img/3/0/4/49304-10105-58-720.jpg)
Added the rest of the cylinder heads, and the rear engine case.
![Album image #14 Album image #14](/albums/img/5/5/3/293553-10105-96-720.jpg)
Decided to switch to the Starfighter wheel well set.
![Album image #15 Album image #15](/albums/img/5/5/4/293554-10105-28-720.jpg)
Fits nicely, but the tank interferes with the attachment for the landing gear.
![Album image #16 Album image #16](/albums/img/5/5/5/293555-10105-12-720.jpg)
Glue only one side of the landing gear in nacelle, and tape together until cured. This sets the angle of the gear.
![Album image #17 Album image #17](/albums/img/5/5/6/293556-10105-57-720.jpg)
Separate and cut off the inaccurate sway brace. This will be replaced with Aires photoetch.
![Album image #18 Album image #18](/albums/img/5/5/7/293557-10105-89-720.jpg)
Modify the tanks to remove interference with gear leg.
![Album image #19 Album image #19](/albums/img/5/5/8/293558-10105-63-720.jpg)
A little Gunze H58 for good luck.
![Album image #20 Album image #20](/albums/img/5/5/9/293559-10105-63-720.jpg)
Final assembly with black wash and additional glycol tank from Aires set. Additional landing gear components to come.
![Album image #21 Album image #21](/albums/img/5/6/0/293560-10105-53-720.jpg)
Completed the rescribing of the fuselage.
![Album image #22 Album image #22](/albums/img/5/6/1/293561-10105-46-720.jpg)
Aires nose well (left), Starfighter (right). Will use Aires so I can slip some weight along side.
![Album image #23 Album image #23](/albums/img/5/6/2/293562-10105-85-720.jpg)
Rudder pedals (and a Hong Kong dollar!)
![Album image #24 Album image #24](/albums/img/5/6/3/293563-10105-81-720.jpg)
Cockpit and nose well fit without major sanding. In my experience that is unusual for Aires.
![Album image #25 Album image #25](/albums/img/5/6/4/293564-10105-29-720.jpg)
Believe it or not, this amount of weight (26 g) is barely enough. It may not work.
![Album image #26 Album image #26](/albums/img/5/6/5/293565-10105-11-720.jpg)
Added some card stock to fill the slot for the base. Slice off when glue is dry and sand.
![Album image #27 Album image #27](/albums/img/5/6/6/293566-10105-95-720.jpg)
Some more weight in the forward portion of the drop tank. This will have little effect, but I figured why not.
![Album image #28 Album image #28](/albums/img/5/6/7/293567-10105-85-720.jpg)
Fuselage and wings together - and it looks nose heavy. But the main gear are at the balance point.
![Album image #29 Album image #29](/albums/img/5/6/8/293568-10105-40-720.jpg)
After a coat of Alclad Grey, she can just as easy set on her tail!
![Album image #30 Album image #30](/albums/img/5/6/9/293569-10105-61-720.jpg)
Part of a clear plastic knife...
![Album image #31 Album image #31](/albums/img/5/7/0/293570-10105-70-720.jpg)
...becomes a lens with green bulb. Magic!
![Album image #32 Album image #32](/albums/img/5/7/1/293571-10105-24-720.jpg)
Quickboost blades are too long (lower blade is correct length), and hole in jig is too small for the hub. Come on guys, test your products!
![Album image #33 Album image #33](/albums/img/5/7/2/293572-10105-38-720.jpg)
She's blue! 🙂 🙂 🙂
![Album image #34 Album image #34](/albums/img/1/4/8/296148-10105-65-720.jpg)
I made a new nose gear door from a piece of beverage can and some styrene rod.
![Album image #35 Album image #35](/albums/img/1/4/9/296149-10105-98-720.jpg)
Adding the ignition harnesses...
![Album image #36 Album image #36](/albums/img/1/5/0/296150-10105-25-720.jpg)
This adds a lot to the engines.
![Album image #37 Album image #37](/albums/img/1/5/1/296151-10105-62-720.jpg)
Engine mounts added to the front of the nacelles.
![Album image #38 Album image #38](/albums/img/1/5/2/296152-10105-48-720.jpg)
Exhausts cleaned up and ready for painting. Very delicate!
![Album image #39 Album image #39](/albums/img/1/5/3/296153-10105-23-720.jpg)
Stickers! All the markings came from the spares box.
![Album image #40 Album image #40](/albums/img/1/5/4/296154-10105-94-720.jpg)
The Starfighter wheel wells really do look nice.
![Album image #41 Album image #41](/albums/img/1/5/5/296155-10105-58-720.jpg)
10 AZ (Bu No 80528) was an F7F-3, so I didn't have to scribe in any camera doors.
![Album image #42 Album image #42](/albums/img/1/5/6/296156-10105-90-720.jpg)
I added some sway braces from the spares box to the drop tank - compare with kit as molded.
![Album image #43 Album image #43](/albums/img/1/5/7/296157-10105-16-720.jpg)
These are the Brengun USN wheel chocks - I'm going to use these if she's ends up a tail sitter.
![Album image #44 Album image #44](/albums/img/1/5/8/296158-10105-20-720.jpg)
Squadron (Falcon) vacuform canopies and the kit part.
![Album image #45 Album image #45](/albums/img/1/5/9/296159-10105-69-720.jpg)
Kit canopy is a perfect fit inside the vacuform - hmmm....
![Album image #46 Album image #46](/albums/img/1/6/0/296160-10105-93-720.jpg)
I made some mods to the engine mounts and reattached. Also, the fuselage has a coat of semi-gloss varnish.
![Album image #47 Album image #47](/albums/img/1/6/1/296161-10105-51-720.jpg)
Alclad stainless steel and Gunze Clear Orange and Clear Blue for heat effects.
![Album image #48 Album image #48](/albums/img/1/6/2/296162-10105-59-720.jpg)
I painted the ends of the exhausts - I didn't drill them out!
![Album image #49 Album image #49](/albums/img/1/6/3/296163-10105-98-720.jpg)
Everything looks good except the port exhausts - the parts are wrong and I'll need to scratch-build.
![Album image #50 Album image #50](/albums/img/3/7/9/296379-10105-83-720.jpg)
This will have to do for the scratchbuilt port exhausts. The styrene rod is just a wee bit too small but the next size up is too big!
![Album image #51 Album image #51](/albums/img/7/1/5/296715-10105-40-720.jpg)
The framework holding the cowl ring is a photoetch piece that you fold up and attach to the engine mounts.
![Album image #52 Album image #52](/albums/img/7/1/6/296716-10105-52-720.jpg)
The cowling rings are made of resin and provide a little more weight up front to help the balance.
![Album image #53 Album image #53](/albums/img/7/1/7/296717-10105-15-720.jpg)
Forgot to show this earlier, but the exit ducts for the oil coolers in the top of the wings were opened up.
![Album image #54 Album image #54](/albums/img/5/3/9/297539-10105-49-720.jpg)
![Album image #55 Album image #55](/albums/img/5/4/0/297540-10105-44-720.jpg)
![Album image #56 Album image #56](/albums/img/5/4/1/297541-10105-21-720.jpg)
![Album image #57 Album image #57](/albums/img/1/7/6/298176-10105-62-720.jpg)
Finished!!
![Album image #58 Album image #58](/albums/img/1/7/7/298177-10105-23-720.jpg)
![Album image #59 Album image #59](/albums/img/1/7/8/298178-10105-37-720.jpg)
![Album image #60 Album image #60](/albums/img/1/7/9/298179-10105-77-720.jpg)
![Album image #61 Album image #61](/albums/img/1/8/0/298180-10105-17-720.jpg)
![Album image #62 Album image #62](/albums/img/1/8/1/298181-10105-99-720.jpg)
![Album image #63 Album image #63](/albums/img/1/8/2/298182-10105-44-720.jpg)
![Album image #64 Album image #64](/albums/img/1/8/3/298183-10105-31-720.jpg)
![Album image #65 Album image #65](/albums/img/1/8/4/298184-10105-61-720.jpg)
![Album image #66 Album image #66](/albums/img/1/8/5/298185-10105-75-720.jpg)
![Album image #67 Album image #67](/albums/img/1/8/6/298186-10105-38-720.jpg)
![Album image #68 Album image #68](/albums/img/1/8/7/298187-10105-24-720.jpg)
![Album image #69 Album image #69](/albums/img/1/8/8/298188-10105-88-720.jpg)
Skinny bugger!
![Album image #70 Album image #70](/albums/img/1/8/9/298189-10105-32-720.jpg)
![Album image #71 Album image #71](/albums/img/1/9/0/298190-10105-65-720.jpg)
Not many years apart!
![Album image #72 Album image #72](/albums/img/1/9/1/298191-10105-50-720.jpg)
The F7F was supposed to be the Tomcat, but US Navy rejected the name saying it promoted "female promiscuity."
Yorumlar
2 9 January 2013, 03:19
![](/profiles/img/10105-s.jpg)
Hi mates!
The Tigercat is underway, with progress on the engines, the re-scribing of the fuselage, and the cockpit. Have a look at the new pictures and captions. Plus, there's fresh popcorn! Made with peanut oil, so it tastes the best and is most likely bad for your health!
Raise your hands if you have a question, I will answer one at a time so behave and wait your turn. 🙂
15 January 2013, 03:48
![](/profiles/img/10105-s.jpg)
All good pilots bring a "range extender." Where is your empty bottle? 🙂
15 January 2013, 04:04
![](/profiles/img/11725-s.jpg)
Hot diggity! One that I've got in the works...but I don't have all that fancy stuff.
Stuff I see here...is it safe to try it at home?
15 January 2013, 06:26
![](/profiles/img/10189-s.jpg)
The saw looks menacing somehow, are you trying to impress the plastic to submit it into fitting? 😄
15 January 2013, 08:40
![](/profiles/img/10105-s.jpg)
Burkhard - The saw is to threaten the resin, so it behaves. The plastic fits together perfectly!
Kelly - Well, I'm trying it at home, so I hope it's safe! 🙂
15 January 2013, 13:47
![](/profiles/img/10105-s.jpg)
The Texas Razor Saw Massacre - doesn't sound as good as chainsaw, does it? 🙂
15 January 2013, 13:56
![](/profiles/img/10105-s.jpg)
As I've said before, I'm a lousy scriber. To be fair to myself, this is the first time I've attempted an entire fuselage. I was looking at my re-scribing efforts closely last night, and some panel lines are deeper than others. Some are too deep entirely. Time for some Mr. Surfacer to partially fill them back in, methinks! 🙂 I love this hobby...
15 January 2013, 15:05
![](/profiles/img/10427-s.jpg)
That's a nice work bench, big enough to lay it all out...
Ready ? Set, go!
19 January 2013, 16:26
![](/profiles/img/11289-303-s.png)
What happens when you have to sneeze Bill?
Aren't you affraid taht some parts could fly away?😉
19 January 2013, 16:35
![](/profiles/img/10105-s.jpg)
There's more progress on the Tigercat. The cockpit is basically done, just need to finish the instrument panel. I've added the rest of the cylinder heads to the engines, plus added the rear engine case. If you look close at the engine picture, you'll see two push-rod tubes. I have to add 72 of those total for both engines! They're 3.75mm long! Arghhh! I've also started the major nacelle surgery, to make way for a PE wheel well, plus all the framework for the engine mounts. As you can see, the PE ceiling was way to long - either Aires screwed up or I've made a really big mistake. But my measurements indicate that the engine should end up in the right place. Hmmm...stay tuned. Same bat-time, same bat-channel! Cheers!
21 January 2013, 01:49
![](/profiles/img/10105-s.jpg)
I finished putting the PE in the port nacelle, after I figured out how I had to modify it. I then gave it a quick layer of Testors Zinc Chromate Green just to see if I was on the right path to making it work. I think it will be OK, I'll try to post some pictures tonight.
By the way, my references say Interior Green in the cockpit (black instrument panel and console), Zinc Chromate Green in the wheel wells, and Glossy Sea Blue for the landing gear legs and wheel hubs. That seems to match the colour photos that I've found from the period, but of course it does not necessarily match the restorations and air racers around today. I hate Zinc Chromate Green, it's too "lime" for my taste. I guess a nice dirty wash in the gear bays will tone it down a bit... 🙂
21 January 2013, 18:06
![](/profiles/img/10427-s.jpg)
Yep, because of the scale, artificial shading becomes all the more important. Then you may want to give anything that stands out a dry brush highlight. Then comes the dirt: you will never find a clean LG bay, unless it has just received a pressure wash, and besides...real warhorses are downright dirty, while racers are usually spotless...😢
21 January 2013, 19:01
![](/profiles/img/11725-s.jpg)
Uh...I think the zinc chromate thing is a bit overplayed, too. I keep expecting to find it in all sorts of cockpits, cargo bays, and landing gear bays, but what I tend to find is metallic finishes, blacks and whites...usually mixed blacks and whites, with grays, too. The zinc chromatic is there, but it is, as noted, often muted with age, scratching and the patina of regular use.
21 January 2013, 21:04
![](/profiles/img/10105-s.jpg)
All depends on who built it, when they built it, etc. The only colour uglier than Zinc Chromate Green is Zinc Chromate Yellow. 🙂
21 January 2013, 21:46
![](/profiles/img/11725-s.jpg)
I'm noticing that 'Interior Green' isn't far from 'Zinc Chromate Green'....is that supposed to be the case? I was under the impression that the Interior was a distinctly darker and more muted green.
Anyway....How's the Tiger, anyway?
2 February 2013, 03:39
![](/profiles/img/10105-s.jpg)
The Tigercat is on hold while I tend to a few other things. Here is everything you need to know about US interior colors:
ipmsstockholm.org/ma..erior_colours_us.htm
2 February 2013, 15:38
![](/profiles/img/11725-s.jpg)
Great link! It confirms so many of my suspicions regarding colors and applications. Thanks, Bill.
2 February 2013, 18:47
![](/profiles/img/10105-s.jpg)
I haven't worked on this project lately. I will have to get it down from the Shelf of Doom now that some folks have taken a seat! 🙂
31 August 2015, 14:23
![](/profiles/img/14143-361-s.jpg)
Do you think that the saw is big enough?🙂 by the way Bill: more than 10 years ago I went the same way and rebuild the -3 to the prototype.
modellversium.de/gal..gercat-monogram.html
31 August 2015, 16:11
![](/profiles/img/10105-s.jpg)
Excellent work on the Tigercat prototype, Bernhard. That is really well done! 👍 👍 👍
1 September 2015, 00:04
![](/profiles/img/26441-134-s.jpg)
Bill, did you ever finish this one? I was reading through your wheel well challenges on Brit Modeller, but the thread just sorta stops. I'm scratch-building some wheel wells for my project, so the thread was very informative.
9 November 2016, 00:01
![](/profiles/img/10105-s.jpg)
Alas, it is on the shelf of doom awaiting a KUTA. (Actually it's on top of a pile of kits right below my workbench.) It seems other projects keep getting in the way. Maybe when I finish this resin Buccaneer...
9 November 2016, 03:21
![](/profiles/img/10105-s.jpg)
OK, you guys talked me into it. I've started this build up again. It is officially off of the shelf of doom! Some new pictures added, too. She's getting a coat or two of Glossy Dark Sea Blue right now.
22 November 2016, 01:27
![](/profiles/img/10105-s.jpg)
Several photos have been added to the Tigercat album. She's coming along well, but I'm really disappointed in the Aires detail set. So many errors and mistakes - I've had to modify almost every part to make it work, and some parts (like the photoetch wheel wells) just didn't work at all. Now I have to scratch-build some exhausts because they didn't realize that the exhausts on the port and starboard side are not the same! They are mirror images of each other. Very frustrating. But on the bright side, she is now sitting up properly - still dangerously close to being a tail sitter, but I still have to add the front cowling and props. I think when all is said and done a good wind will still set her back on her tail, just like the real plane! 🙂
7 December 2016, 03:02
![](/profiles/img/20442-422-s.jpg)
Remarkable how much detail you have crammed into such a small scale Bill. Excellent result so far.
7 December 2016, 07:21
![](/profiles/img/11067-733-s.jpg)
She's a beauty Uncle ! But why, of all the choices, did you pick the gloss blue scheme ? 😉
7 December 2016, 07:45
![](/profiles/img/user-s.jpg)
Thanx for the heads up re the Aires detail set. Have been thinking of doing much the same but never had the courage
7 December 2016, 10:24
![](/profiles/img/16661-726-s.jpg)
It`s always stunning to see how you manage to get this incredible amont of detail into these rather
tiny scaled planes, simply excellent !
7 December 2016, 11:00
![](/profiles/img/user-s.jpg)
and then you don't see a few updates, and the plane is almost completed... nice build so far, very nice...
What did you use for the dark sea blue?
7 December 2016, 12:38
![](/profiles/img/10105-s.jpg)
Thanks mates! 🙂
Bart - the Dark Sea Blue is Model Master FS15042 #1717. It's one of the few Testors paints that I like.
Wilfried - I don't think there are many choices other than Dark Sea Blue for an F7F-3. The night fighters, F7F-3N, had a black scheme with red letters in Korea but they also had a different nose to accommodate the radar. If I can get my hands on the Pavla/Octopus 1:72 kit of the F7F-3N I'd love to do that. The other possibility for the F7F-3 would be a fire bomber, and those schemes were colorful. I would need a conversion set for the belly tank though. Anyway, I like the Dark Sea Blue scheme - I wish the USN planes were still painted that way. I'm going to a USN Anniversary F-18 in the WWII tri-color scheme as it appeared for the celebration. That will be cool!
Getting the decals together from the spares box was a lot of fun. All individual letters, and the "Z" on top of the wing is actually made from pieces of several other letters as I didn't have a Z that big. Remind me not to do that again! Now I'm off to play with lead wire and see if I can make some exhausts - if anyone asks, I do not recommend the Aires detail set...
7 December 2016, 14:32
![](/profiles/img/15497-946-s.jpg)
it's a beauty! I remember the kit from ages ago - you're a magician!
7 December 2016, 17:57
![](/profiles/img/10105-s.jpg)
I made a sample of the port exhaust using styrene rod. It's not perfect, but it will have to do. I posted a photo showing it with the kit part - you can see what I mean by mirror-image, plus the pattern of long/short pipes is reversed (since each bank of cylinders has an odd number). Now I have to go make another one just like this - darn twin engine fighters! 🙂
Wilfried - I just noticed you had a smiley face next to your comment about "all the choices" I had to paint the model. You knew there was only one all along! You funny guy! I need to read these comments more thoroughly... 🙂
8 December 2016, 04:09
![](/profiles/img/11725-s.jpg)
I'm with you, Bill. I like the Deep Sea Blue scheme. Much better than the seagull colors that followed.
8 December 2016, 18:22
![](/profiles/img/10105-s.jpg)
Kelly - 26 grams went into the nose, and below, alongside, and behind the cockpit. Photo 25 shows the weight in place. If someone were building the kit with the nacelles as is, I would put some additional weight in there. I couldn't do that on this build due to the exposed engines. As it is now, the main gear legs are essentially right at the balance point.
8 December 2016, 18:58
![](/profiles/img/13680-285-s.jpg)
Hey Bill, I am also building the F7F-3. I have added a lot of scratch built parts, trying to get it ready for painting. I dont think I have 26 g of weight in the nose. You can find photos in my albums. I have not done much work on it in the pass few days. Hope to get back at it soon.
8 December 2016, 19:10
![](/profiles/img/10105-s.jpg)
Thanks guys! I added a couple more pictures that show the cowl rings attached. Once I add the props, that will be it for the engines/nacelles! Then I can finish the windscreen/canopy and the antennae. I kinda like how it's turning out, maybe I won't bin it after all. 🙂 🙂 🙂
John - looks like you've bitten off quite a big project too! The F7F was such a cool plane - I think you'll need more weight up front than what I saw in your photos. Since you have her all buttoned up, you can always glue the wheels to a base.
10 December 2016, 02:49
![](/profiles/img/18594-868-s.jpg)
See Cobra Company for the F7F-3N nose and backseat conversion kit; cobracompany.com/72007.htm
See Lone Star Models for the F7F fire bomber tank conversion kit; lonestarmodels.com/Conversions1-72.html
And decals; lonestarmodels.com/Decals.html
Also see DRAW Decals for F7F fire bomber decals; shopdrawdecal.com/Pr..uctCode=72%2DF7F%2D1
And; shopdrawdecal.com/Pr..uctCode=72%2DF7F%2D2
10 December 2016, 04:44
![](/profiles/img/13680-285-s.jpg)
Thanks Bill, That is what I will end up doing. I do have one more kit I am saving to do the Night fighter, so now I know about the weight. I also have the Cobra Conversion set and will give it a go soon.
10 December 2016, 14:26
![](/profiles/img/10105-s.jpg)
I've finished the Tigercat - have a look at the new photos. Time to build something else! Cheers, Bill
17 December 2016, 02:22
![](/profiles/img/user-s.jpg)
Officially jealous... That's a nice one... Maybe a light wash in the panellines of the white decals, but otherwise... Excellent
17 December 2016, 07:43
![](/profiles/img/16661-726-s.jpg)
Fantastic Tigercat Bill ! It`s simply amazing to see your ablity to squeeze such a high level of detailing out of an rather old and basic kit like this one. 👍 👍
17 December 2016, 09:08
![](/profiles/img/26441-134-s.jpg)
I was clamouring for you to finish this one so I could follow along to use it for my own build... but it's like trying to follow a bird that's taken flight. All I can do is stand and stare... wow.
17 December 2016, 10:34
![](/profiles/img/16386-829-s.jpg)
Very briliant result with a very nice arrangement with the other Grumman cats
17 December 2016, 15:05
![](/profiles/img/10105-s.jpg)
Thank you everyone for the nice comments. I really appreciate reading them. I think my next build will be the Gloster Meteor F.3 and then in April I start an F-111 group build on Britmodeller. I'm going to try and convert the Hasegawa F-111C/G into the USN F-111B prototype. That should be interesting, as it's more than just a nose-job. Cheers, Bill
18 December 2016, 15:38
Album info
My latest bout of insanity has rendered me powerless to avoid starting this project. This is the ageless Monogram Tigercat kit, dolled up with the Aires Super Detail Set.