Dornier 335A-1 Tamiya
Yorumlar
1 13 December 2014, 21:40
![](/profiles/img/11475-s.jpg)
Ta dan kan ik uiteraard niet achter blijven ik volg deze ook
16 December 2014, 08:39
![](/profiles/img/14213-529-s.jpg)
Pit is done. Seatbelts are from Eduard. Looking good enough OOB 👍
16 December 2014, 20:57
![](/profiles/img/14213-529-s.jpg)
Dankje Rob. Dit is volgens mij een heel erg fijne kit om te bouwen. Ik heb ooit eens die tweezitter gehad..nu al spijt dat ik hem verkocht heb😄
17 December 2014, 20:26
![](/profiles/img/14213-529-s.jpg)
Mike, we'll keep it in English from now on. Better for everyone 😉
17 December 2014, 21:26
![](/profiles/img/11475-s.jpg)
I know Arne don't rub it in But it did find a good home Besides i Always can start building the two seater some....day
17 December 2014, 22:12
![](/profiles/img/user-s.jpg)
Nice cockpit, just to "copulate with ants", the seatbelts won't hang like this in reality
18 December 2014, 11:50
![](/profiles/img/14213-529-s.jpg)
I think i know what you mean Bart. They should be hanging more over the "bump".
18 December 2014, 15:27
![](/profiles/img/14213-529-s.jpg)
Well Bart, i could be fixed. But not without some destructive measures. Think i will keep it like it is.. learning moment..
19 December 2014, 21:02
![](/profiles/img/13335-577-s.jpg)
looks good erik .
lol ,i just cut some pieces from the sprue for the cockpit 😮
Rob already started?
28 December 2014, 20:55
![](/profiles/img/11475-s.jpg)
That explains a lot.
Arne I just finished opening up the rear engine bay in preparation for installing the engine i start with the cockpit soon(maybe tomorrow)
28 December 2014, 23:10
![](/profiles/img/11224-741-s.jpg)
tolle Arbeit , gefällt mir 🙂 👍 die Do 335 immer 🙂 ich werde in Zukunft bei Martien übersetzen lassen 😉
29 December 2014, 00:38
![](/profiles/img/14213-529-s.jpg)
Danke Jens. Die Do335 ist eines schones flugzeug. Was wollen sie ubersetzen lassen bei Martien? Sorry for my German, it's not quite good 😄
30 December 2014, 19:23
![](/profiles/img/11224-741-s.jpg)
Sorry for my German, mein english ist Google Translate , also Danke für das recht gute Deutsch von Dir 👍
30 December 2014, 22:10
![](/profiles/img/11475-s.jpg)
Duurt nog wel even voordat ik ook zover ben alles ligt nu zowat stil maar komt wel gauw weer op gang denk ik
11 January 2015, 19:51
![](/profiles/img/11224-741-s.jpg)
Moin Erik , welche Version der 335 soll es werden ?? welche Kennung ist gedacht ?? denn , einige waren Naturmetall am Unterrumpf ! Gruss Jens
15 January 2015, 19:08
![](/profiles/img/14213-529-s.jpg)
Ha Jens, es werden den A-1 Version. Keine Kennung, nur ein Serienummer: 1`3. Naturmetall unterrumpf is sehr schon oder mein ist RLM76 am unterrrumpf.
Ich hoffe, dass Sie mein Deutsch verstehen 😄
15 January 2015, 20:28
![](/profiles/img/11224-741-s.jpg)
Sicher Erik , dein Deutsch ist besser als meine Versuche mit Google Translate 😄 😄 😄 , Für die 1_3 kann man gute Referenzen im Internet finden , ich freue mich auf Deine Bilder mit der ganzen Farbe 👍
15 January 2015, 23:04
![](/profiles/img/14213-529-s.jpg)
Added the decals. Aftermarket swastika is used because i think the kit swastika is not correct. All black instead of white outline only.
I'm thinking of giving this bird a satin coat instead of matt i usually use.
30 January 2015, 20:03
![](/profiles/img/11475-s.jpg)
So fast I will be happy when I will be able to close the fuselage of my DO 335 this week(propably not)
30 January 2015, 22:14
![](/profiles/img/14213-529-s.jpg)
Thanks mates. I still do not know what kind of finish i'll give it. A flat one or a satin. I usually use Xtracolor flat varnish, wich is really really matt. I also have Xtracolor satin varnish but never used it. Gonna spray the satin on a old model today, we'll see.
3 February 2015, 09:15
![](/profiles/img/user-s.jpg)
very nice work on the camo, I'd opt for the satin varnish. Normally I use the varnishes from alclad for the last cote, splendid stuff to work with...
3 February 2015, 13:23
![](/profiles/img/10427-s.jpg)
These aircraft were not used as much as other operational types, so I would go for a satin finish with wear limited to main access panels. Don't forget this aircraft was built for speed, so I expect its finish to have been more glossy than the average fighter.
3 February 2015, 17:33
![](/profiles/img/11475-s.jpg)
Erik, check some pictures on internet to see what finish would suit best. the pictures I saw where mostly matt finish
4 February 2015, 09:34
![](/profiles/img/14213-529-s.jpg)
Thanks for the help guys. I've used the satin finish and it turned out good i think. Not to satin but a bit of flat. I like it. Made some pictures in daylight, it looks nice. Too bad i have some silvering on some stencils but i can live with that.
4 February 2015, 15:39
![](/profiles/img/11475-s.jpg)
is looking good Erik. Ik zie hem morgen wel denk ik zal ik de mijne(nog lang niet zo ver )morgen meenemen??
4 February 2015, 15:58
![](/profiles/img/user-s.jpg)
Looks very good to me. I don't see a lot of silvering, but I always try to remove as much of the carrierfilm as I possibly can to avoid it...
4 February 2015, 16:03
![](/profiles/img/14213-529-s.jpg)
Bart, the silvering is on the red stencils on the horizontal stabilizers, it's minimal but it's there
4 February 2015, 16:18
![](/profiles/img/15629-913-s.jpg)
apparently there is a technique to remove the carrier film altogether using enamel thinners.
I have yet to work it out but I heard about it from Flory Models, would love to know what it is exactly 🙂
but yes, great work dude 🙂
4 February 2015, 16:25
![](/profiles/img/14213-529-s.jpg)
Well that is something worth of checking out Choppa. Altough with a proper gloss base and proper quality decals the carrier film almost never is a problem i think
4 February 2015, 21:05
![](/profiles/img/15629-913-s.jpg)
Yeah this is a technique I definitely want to find out about because it removes the thickness from the decal so you don't get any washes collecting round the edges of the decals, plus it guarantees absolutely no silvering ever again 🙂
Most of the time I don't get silvering anymore but sometimes I do on the smaller stencils, the other handy thing about this technique is apparently is that you can apply it directly to a matt finish 🙂
4 February 2015, 21:15
![](/profiles/img/15888-619-s.jpg)
My 2 cents worth is that I can ruin almost any decals made by any company, I've taken to painting on the big markings and dry transfers for stencilling.
4 February 2015, 23:26
![](/profiles/img/user-s.jpg)
Very nice job on this one... this one is moving up in my to do list... hope to get it as beautiful as this one...
10 February 2015, 14:30
![](/profiles/img/14213-529-s.jpg)
Thanks mates! Bart, you really need to build one. It is a awesome kit. Thanks for the kind words 🙂
10 February 2015, 14:44
![](/profiles/img/11475-s.jpg)
He Erik looking very good indeed Also very good pictures too now I know where to go too when my Dornier will be ready. Do you already know what the next project will be
10 February 2015, 17:11
![](/profiles/img/14213-529-s.jpg)
Thanks mates!! No Rob i haven't decided yet what to start next. The misses demanded some attention now 😄.
Great to see you all like it 👍
10 February 2015, 19:40
![](/profiles/img/13335-577-s.jpg)
It looks like a killer build Erik ! The xtra color satin is perfect for the job . Dont think mine will be as good as yours.
10 February 2015, 20:25
![](/profiles/img/14213-529-s.jpg)
Thanks James! Yes, the cylindrical nose weight is enough to hold it on it's nose wheel. But, when you want to add a resin aftermarket rear engine you should put in more I guess. Looking forward to your build mate!
21 September 2017, 06:00
![](/profiles/img/14213-529-s.jpg)
Exactly as mine James, just some masks. Pull your finger out of the booze you drink often(😢) and on to the bench!!
21 September 2017, 20:25