Die Rollbahn
my Goal at the End: Gelbe 10 Uffz. Hans Döbrich, 6./JG 5, Petsamo, Finland, September 2, 1942
Here we go 🙂
some wires added
Black Base followed by Dark Rust
Next Light Rust
and weathering Set D of Tamiya for the finish
The Wheelwells had to be grinded to make the top wing fit properly ** correction!! Eduard numbered the wrong parts for the wheel wells. It used the wells for the 109G with the bigger wheels**
Some minor gaps at the fuselage-wing section when dry fitting. This is easily solved by first glueing the bottom wing, before ...
... stretching the top wing upwards until the the gap is closed for glueing
Finally the last step done. Ready for Paint
I love the MRP colors
Primed
Their primer is very smooth.
I tried a new way of Preshading... this is a first, so lets see what happens
The Yellow has a great Tone, but that little Preshade i made was allready to strong! i had to Reverse most of the Preshade with Primer in order to make the Yellow acceptable.
I hope the RLM78 Blue for the Belly doesnt have to get the same going as the yellow :|
I had to Re-Do the Spinner. My Flat Clear was clogging and had lots of clouds on it. So i removed the color and started again, this time playing with Shadows and Lights.
First Paintjob done. Need to correct the yellow fuselage ribbon
Starting weathering the Lower Wing.
This is how my workbench looks after a projekt. No matter how big your table is, at the end you'll be worklng on a space by 20x20cm 😄
On the finishing line. Only some touches here and there left and i'll call it done
Yorumlar
29 January 2017, 09:14
Bart Goesaert
Me too.. cockpit looks very good.. spinner and screw looks well used and I have to keep the painting method of the exhausts in mind...
Me too.. cockpit looks very good.. spinner and screw looks well used and I have to keep the painting method of the exhausts in mind...
9 February 2017, 09:30
Roger Lustenberger
Thank you guys!! 🙂 please, have a seat and support me to the end. Tipps, hints and feedbacks are always welcome.
@ Bart, the spinner looks alittle too much on the pics than it actually is.
Thank you guys!! 🙂 please, have a seat and support me to the end. Tipps, hints and feedbacks are always welcome.
@ Bart, the spinner looks alittle too much on the pics than it actually is.
9 February 2017, 11:35
Spanjaard
spinner looking good. but it surprise me that you are leaving that mould line in the centre of the exhausts.
spinner looking good. but it surprise me that you are leaving that mould line in the centre of the exhausts.
9 February 2017, 17:51
Spanjaard
my apologies then! i really did not know that. i better remember when i build a 109, otherwise i will probably remove them 🙂
my apologies then! i really did not know that. i better remember when i build a 109, otherwise i will probably remove them 🙂
9 February 2017, 22:04
Roger Lustenberger
No problem 😉 you caught me offäguard! had to check myself first
No problem 😉 you caught me offäguard! had to check myself first
9 February 2017, 22:07
Roger Lustenberger
some progress with Paints made... what do you think? too much?
some progress with Paints made... what do you think? too much?
19 February 2017, 14:35
Razvan Coman
is ok. a single question: on the vertical part of the chair is chipping between seat-belts? i cant tell from picture
Ps u did not used photo etch parts on pedals?
is ok. a single question: on the vertical part of the chair is chipping between seat-belts? i cant tell from picture
Ps u did not used photo etch parts on pedals?
19 February 2017, 18:27
Roger Lustenberger
Hi Razvan, i did some small scatches on the seat, but mostly its actually some crystal glue i used to fix the belts. And for the pedals, i never use the photo etched ones because you wont see it at the end when both halfs are together.
Hi Razvan, i did some small scatches on the seat, but mostly its actually some crystal glue i used to fix the belts. And for the pedals, i never use the photo etched ones because you wont see it at the end when both halfs are together.
19 February 2017, 18:43
arne vd burg
Outstanding job so far Roger , I am watching you progression with great interest.
Outstanding job so far Roger , I am watching you progression with great interest.
2 March 2017, 05:55
Bart Goesaert
It's always nice to see one in non-standard camo's... Splendid work; also how you make the panels come forward...
It's always nice to see one in non-standard camo's... Splendid work; also how you make the panels come forward...
2 March 2017, 10:45
Roger Lustenberger
Hey Bart, Thanks. I added a drop of White into the color and lightend each panels this way. check my Do-335, did it the same way.
Hey Bart, Thanks. I added a drop of White into the color and lightend each panels this way. check my Do-335, did it the same way.
2 March 2017, 11:00
Roger Lustenberger
Slowly getting to an end. Missing the Antena & Clearparts and started with the Base and Figure
Slowly getting to an end. Missing the Antena & Clearparts and started with the Base and Figure
8 March 2017, 07:02
Razvan Coman
Excelent work till now and the color scheme is unusual (in a very good sense) for the 109's
Excelent work till now and the color scheme is unusual (in a very good sense) for the 109's
8 March 2017, 17:40
Roger Lustenberger
Figure is done, the base awaits for the glue to harden and the antenna wire is missing on the Friedrich. This Weekend its getting its Roll-Out
Figure is done, the base awaits for the glue to harden and the antenna wire is missing on the Friedrich. This Weekend its getting its Roll-Out
16 March 2017, 23:21
Roger Lustenberger
There you go, all is completed 🙂 many thanks for your support on the way
There you go, all is completed 🙂 many thanks for your support on the way
19 March 2017, 09:38
Spanjaard
excellent result Roger, beautiful Me109. it was a pleasure to follow and learn 😉
excellent result Roger, beautiful Me109. it was a pleasure to follow and learn 😉
19 March 2017, 10:24