03- Assembling the Wittmann's Tiger I Late

1
June 8, 2020
while we wait for the new airbrush to arrive at the post office to continue painting on the Panther Ausf.G by M.N.H. I'm going to start working on the Tiger I possibly used by Michael Wittmann in the battle of Villers-Bocage, here's the kit!
2
June 9, 2020
taking some notes about the corrections of the kit, what options are correct or not, and things to do in assembly steps!
3
June 9, 2020
4
June 9, 2020
5
June 9, 2020
6
June 9, 2020
start of the basic assembly of the chassis and tower to apply the zimmerit, here correcting the the ejection pins marks!
7
June 9, 2020
while the self-curing resin to cover the marks of the ejection pins is drying, we will work on the rear panel
On top of the rear hull wall, there are 8 small raised locator tabs. These were used with the Feifel filter system in Academy's Early Tiger kit. But, in a Mid or Late Tiger, they should not exist. You should cut these tabs off.
8
June 9, 2020
These raised rectangular frames for mudguard, on the left and right side of the rear hull wall, did not exist in Mid or Late Tigers. They were present in some Early Tigers, but Academy have mistakenly included them in Mid and Late kits.
9
June 9, 2020
The Tiger had an adaptor tool to align the starter handle with the engine.
10
June 9, 2020
On some Academy kits, the tool is glued to the rear hull wall. There is a raised circle to locate it. here the circle was removed, but you can see his shadow yet
11
June 9, 2020
But in a real Tiger, the tool was fixed to 2 small poles, holding it some distance from the hull wall, here made with some useless spare parts!
12
June 11, 2020
Two posts were welded on the Tiger's upper rear plate, for storing the starter adapter. This diagram shows one post
13
June 9, 2020
and here the two holes in the hull wall to guide the tool were he will be fixed after the zimmerit coat be applied
14
June 11, 2020
In December 1942, when sheet-metal exhaust shields were added to the Tiger as standard, the posts were rotated 60 degrees about their initial position
15
June 11, 2020
The adapter was now held vertical, avoiding a collision with the shields.

diagram references from: tiger1.info/EN/Starter-adapter-posts.html
16
June 10, 2020
preparing the pieces for apply the Zimmerit
17
June 10, 2020
preparing the pieces for apply the Zimmerit
18
June 10, 2020
preparing the pieces for apply the Zimmerit
19
June 10, 2020
preparing the pieces for apply the Zimmerit
20
June 10, 2020
preparing the pieces for apply the Zimmerit
21
June 10, 2020
I am using epoxi putty to my Zimmerit!
22
June 10, 2020
mix the two equal parts of epoxi putty and throw a lot of talc on the table! (I made a short board with 0.20mm high jigs, it kills me a lot of the time it takes to open the dough)
23
June 10, 2020
put the putty on top of the talcum and slowly open it with your fingertip
24
June 10, 2020
go opening the putty slowly and without forcing too much, turn and powder it constantly so that it does not stick to the roll or the table!
25
June 10, 2020
when the putty becomes in the size of the piece what you want to cover, you will wet your finger and wet the place that will receive the putty and a litle the contact side of the outty! otherwise it will not stick, it will go wrong and you will curse me! 😄
26
June 10, 2020
and the putty has to be VERY thin! ( so the thinner you open the putty, better he is!!! So then throw more talcum and open more!)
27
June 10, 2020
and again, mooooooore talcum! 😄 😄 😄

but now for the tools!
28
June 10, 2020
as you pass the tool, the epoxy will get thinner and thinner and spread! (that's why I used the tape to delimit the area I wanted to leave without zimmerit and also to help remove the excess!
29
June 10, 2020
after cleaning the excess this is the result!
30
June 11, 2020
rear panel done!
31
June 11, 2020
Left side done! now the zimmerit on lower hull is 75% complete, now I gonna set aside for dry properly and tomorow I'm gonna make the front plate and finish the zimmerit of lower hull
32
June 11, 2020
one error associated with the turret are the turret bin and the "notch" that faces the turret: this does not extend all the way to the base of the bin as in the kit, but only about 1/3 of the way down. You will need to close with plasticard and sand smooth the fill (check out this cross-section of a proper bin).
33
June 11, 2020
the fixed turret bin,
34
June 11, 2020
35
June 11, 2020
Academy's Late and Mid Tiger kits re-use the turret side hatch from their Early kit (part K9). This is a round hatch with bevelled sides which is suitable only for an Early Tiger. But, the real hatch on these Tigers was a simple disc without bevelled sides.

Let's go try to correct him! 😄
36
June 12, 2020
now like the real hatch on Mid and Late Tigers, just a simple disc without bevelled sides.
37
June 12, 2020
and we cover with the epoxy putty
38
June 12, 2020
remove the excess of the areas we don't want to cover!
39
June 12, 2020
and make our magic with the Zimmerit! 😄 😉
40
June 12, 2020
Let's start the turret Zimmerit
41
June 12, 2020
42
June 12, 2020
I forgot to take a picture of the Mantlet and the zimmerit on the other side of the tower before setting it up!
43
June 12, 2020
but it was a very pleasant view
44
June 12, 2020
the rear view of the tower and the rear panel!
45
June 12, 2020
the scape hatch aligned like the real one!
46
June 14, 2020
the front hatches for driver and radio operator are ready too!
47
June 12, 2020
enjoying the view of your beautiful sexy back, here's a little dry-fit to see how things will be after it's finished!
48
June 12, 2020
then you buy a lot of tools to make zimmerit and they don't go into the corners to do their job and you have to appeal to PS plates and make a tool in a hurry!

😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄 😄
49
June 12, 2020
and this is the photoshoot sequence of the work of the day!
50
June 12, 2020
51
June 12, 2020
52
June 12, 2020
53
June 13, 2020
shaping with hot water the new commander's cupola MG ring made in 0.5mm polystyrene sheet
54
June 13, 2020
glued in place, much better than from the comes in the kit! 😄
55
June 14, 2020
The later Tigers were fitted with holders on the turret sides for spare links of track. I follow the diagrams from Hillary Doyle who show the form and position of the holders.
56
April 6, 2021
very different from the others pictures of the assembly, but this os here Just because I like this picture a lot, and show the zimmerit almost done!
57
June 14, 2020
58
June 14, 2020
59
June 14, 2020
doing the U-shaped metal rod
60
June 14, 2020
The hook could be locked by putting this U-shaped metal rod
61
June 14, 2020
62
June 14, 2020
63
June 16, 2020
This diagram shows how a track link was held in its holder. Note that only the wider 'combat' track links would fit. Also note that the track guide horns are towards the lower end of the link. The pin on the bottom support fits into the hole for the track pin.
64
June 14, 2020
this is a dry-fit to show how the spare tracks will be in the end!
The lower and upper parts of supports were slightly offset. They were welded at right angles to the hull armour.
65
June 14, 2020
let's improve the escape muffler, for the center hole 1mm drill
66
June 14, 2020
for the satellite holes 0.4mm holes
67
June 14, 2020
0.4mm cooper wire for supports
68
June 14, 2020
the head of mufflers in place
69
June 14, 2020
cut the excess and ready! easy peasy!
70
June 14, 2020
let's do it again in the next muffler
71
June 14, 2020
dry-fit in place!
72
June 14, 2020
looks good to me! what's next step to do???? 😄 😄 😄
73
June 14, 2020
let's go to the steel cable, I prefer to make mine at home, wrapping copper wire! for the thin cable I use 4 wires and I'm rooting with the dremel!
74
June 14, 2020
gluing the supports in the cables!

I will make yet the heads of cables!
75
June 14, 2020
and this is how he will be in place!
76
June 15, 2020
0.6mm hole for the perfect adjustment of cable!
77
June 15, 2020
the final piece! satisfies me 😛
78
June 15, 2020
I painted the lower hull in flat black to decrease the visibility of the interior through the ventilation slots of radiator!
79
June 15, 2020
80
June 15, 2020
lots of wheels to clean
81
June 15, 2020
now lets start to make one line of the wheels so you can easily remove them without having to assemble them all individually when painting
82
June 15, 2020
I usually don't need more than CA glue to do this, but these wheels were too far apart, so I decided to use a 0.5mm chock between them, and so stick them firmly and well hidden!
83
June 15, 2020
when the wheels of the middle rows are glued, the chocks are well hidden behind all the external ones and will no longer be seen!
84
June 15, 2020
the wheels of the outer row are not yet glued together as this makes it easier to correctly paint the wheels of the second row!
85
June 15, 2020
firmly and strong!
86
June 15, 2020
the idler is very misaligned when placed correctly, so it must be relocated to the correct position, but there is a large space in its axle bar!
87
June 15, 2020
to correct it I used the polly cap of the tractor wheel that I did not use, cut it in half and made a wedge as needed!
88
June 15, 2020
this os the final piece in your right place! I strongly recommend that you do not forget to use the polly caps of the tensioning wheels, they are sorely needed!!!
89
June 15, 2020
Some of Academy's kits have a detail on the rear mudguards that should not be present.
90
June 15, 2020
The mudguards, parts B4 and B5, have cross-shaped holes in them. But, in a Mid or Late Tiger, these holes were simple rectangles.
91
June 15, 2020
corrected and ready for rest in their last place!
92
June 15, 2020
0.5mm cooper wire used to make the wire of notek lights and MG34 in their place of ball mount
93
June 15, 2020
watch out allies airplanes, keep them in sight!!! 😄
94
June 15, 2020
now I have to think how to make the belt for bullets and put him in this MG-34 on the commander's cupola!
95
June 18, 2020
well, I think the assembly stage is over, here some photoshots of the complete assembly!
96
June 18, 2020
97
June 18, 2020
98
June 18, 2020
99
June 18, 2020
100
June 18, 2020
101
June 18, 2020
102
June 18, 2020
103
June 18, 2020
104
June 18, 2020
105
June 18, 2020
106
June 18, 2020
now the torture of painting begins! 😄 😄 😄 😄
107
June 25, 2020
I found an old Tamiya figure here by stash, I think this one will represent Wittmann now! 😄 😄 😄 😄 😄

Yorumlar

2 8 June 2020, 20:19

Rui S
Belas dicas para zemerit Mate. Bom trabalho. 👍
A pasta adere só com água ao plástico ou colocou alguma cola?

10 June 2020, 15:51

Rafael Lang
obrigado Rui, eu uso somente água, a cola é a propria da massa epoxi! mas já vi um pessoal passando cola liquida por baixo também!

10 June 2020, 18:39

Spanjaard
that zimmerit looks simply amazing!!!!

10 June 2020, 21:52

Rui S
Boa. Quanto tempo demora a secar até poder retirar o excesso e pintar?

10 June 2020, 22:19

Rafael Lang
Rui, na embalagem da que eu uso diz que entre 2 e 4 horas ja está seco, mas eu sempre deixo um bom tempo a mais, coisa de dias, pois eu não monto tão rapido quanto deveria, entao ele seca por dias (as vezes meses) antes de ver o primer (que só o faço depois de tooooda a montagem concluída!)

10 June 2020, 22:53

Rafael Lang
Thank you Spanjaard, I'm trying to do my best on them! 😄😉

10 June 2020, 22:54

Rui S
Hehehe, percebo perfeitamente, Rafael 😄 é mais ou menos o tempo que eu deixo secar as minhas pinturas com óleos. 😄

10 June 2020, 23:01

Rafael Lang
Rui, olha aqui a epoxi putty da green stuff, é perto de você e funciona como essa minha por aqui!

greenstuffworld.com/..inches-with-gap.html

11 June 2020, 05:21

Rafael Lang
e aqui uma sequência de videos que achei de um japonês que ele mostra como abre e aplica de forma bem parecida com a minha!
porem não gosto de como ele abre a massa epoxy ,por isso uso muito talco em pó para evitar de grudar no gabarito que fiz com a altura determinada! facilita muito essa minha ferramenta principalmente se acompanhada de um bom rolo liso!

aqui está os videos da sequência do panther!

Youtube Video

Youtube Video

boa diversão assistindo esses videos todos! 😄 😄 😄 😄

11 June 2020, 05:35

Rui S
Belo progresso Mate. Está ficando impec. 👍

12 June 2020, 19:08

James C
Nice work on the zimmerit 👍

12 June 2020, 19:11

Rafael Lang
obrigado Rui, tento fazer o meu melhor sempre! 😄

13 June 2020, 07:31

Rafael Lang
Thanks James😉

13 June 2020, 07:31

Rui S
Claro que sim Rafael, e como já tivemos oportunidade de ver o seu melhor é muito bom ou excelente.

13 June 2020, 12:29

Rafael Lang
obrogado, mas nem sou tudo isso, tenho minhas falhas ainda 😄 pintura mesmo é a maior delas, é uma coisa que nunca me agrada e ainda não descobri o prazer em fazê-la !

15 June 2020, 04:11