Стрічка новин
Jakko
додав новий фотоальбом.
додав новий фотоальбом.
25 2 July, 20:50
gorby
I think you win this weeks prize for most heavy duty modelling tool. 😄
Looks a very interesting conversion.
I think you win this weeks prize for most heavy duty modelling tool. 😄
Looks a very interesting conversion.
5 July, 06:33
Jakko
> I think you win this weeks prize for most heavy duty modelling tool. 😄
Probably, yeah 🙂 It's a metalworking lathe, so a bit overkill for just turning down the seam on those wheels, but I didn't feel like aching fingers from scraping them down with a knife — I get those even when I hold them in a modelling vice, never mind just between my fingers.
> that kind of set up can tool a real bogie!!
Having seen a disassembled Sherman bogie up close, I must say I think this one is a size too small for that 😉
> I think you win this weeks prize for most heavy duty modelling tool. 😄
Probably, yeah 🙂 It's a metalworking lathe, so a bit overkill for just turning down the seam on those wheels, but I didn't feel like aching fingers from scraping them down with a knife — I get those even when I hold them in a modelling vice, never mind just between my fingers.
> that kind of set up can tool a real bogie!!
Having seen a disassembled Sherman bogie up close, I must say I think this one is a size too small for that 😉
5 July, 08:53
Jakko
@Mr D: that's not the welds yet, it's just the filler needed to plug the gaps 🙁 I'm still debating how to add all the weld seams.
@Ben M: An M2 screw, about 2 cm long, through the hole in the wheel, with a nut to tighten it. It needs to be fairly tight else chances are the wheel will stop as soon as the chisel hits it. On Asuka two-piece wheels, you need to do this before assembling the parts, because the hole on the piece to be glued in is smaller than on the part that has the tyre moulded on it.
@Mr D: that's not the welds yet, it's just the filler needed to plug the gaps 🙁 I'm still debating how to add all the weld seams.
@Ben M: An M2 screw, about 2 cm long, through the hole in the wheel, with a nut to tighten it. It needs to be fairly tight else chances are the wheel will stop as soon as the chisel hits it. On Asuka two-piece wheels, you need to do this before assembling the parts, because the hole on the piece to be glued in is smaller than on the part that has the tyre moulded on it.
9 July, 08:59
Ben M
Thank you, I can envision the setup. I have a small lathe and arthritis in my hands, this technique could help me a lot. Thanks!
Thank you, I can envision the setup. I have a small lathe and arthritis in my hands, this technique could help me a lot. Thanks!
9 July, 11:58
Mr D
Regarding weld's l have seen super glue used through a fine tip, you need steady hand n move in pattern to create weld.
Sorry l was looking at the resin 🤔🤣.
Good stuff be keeping eye
On progress 👍👍
Regarding weld's l have seen super glue used through a fine tip, you need steady hand n move in pattern to create weld.
Sorry l was looking at the resin 🤔🤣.
Good stuff be keeping eye
On progress 👍👍
9 July, 13:30
Jakko
@Ben M: What also works is a modeller's vice. Clamp the wheel in that, scrape down the seam with a straight knife over a third or so of the wheel, then unclamp and turn it, and repeat. If I scrape more than about two or three wheels by hand, my fingers ache enough that I have to stop, so the vice helps a lot. But you also get a lot of plastic scrapings all over your modelling area, so this time, I figured I'd put those in someone else's hobby room instead for a change 😉
@Mr D: Hahaha! The ones on the resin were put there by Resicast 🙂 But I'll now have to make ones that look similar, or at least not out of place next to them. I'm thinking a thin string of two-part epoxy, textured with a sharp tool.
@Ben M: What also works is a modeller's vice. Clamp the wheel in that, scrape down the seam with a straight knife over a third or so of the wheel, then unclamp and turn it, and repeat. If I scrape more than about two or three wheels by hand, my fingers ache enough that I have to stop, so the vice helps a lot. But you also get a lot of plastic scrapings all over your modelling area, so this time, I figured I'd put those in someone else's hobby room instead for a change 😉
@Mr D: Hahaha! The ones on the resin were put there by Resicast 🙂 But I'll now have to make ones that look similar, or at least not out of place next to them. I'm thinking a thin string of two-part epoxy, textured with a sharp tool.
9 July, 17:09
Mr D
Good video 👍, the finish on the flat plate work looks authentic, l think it's had better rough cast look from the brush stippling before he added the putty coat.
Good idea on the weld , epoxy putty best as regular epoxy levels out again.
Good video 👍, the finish on the flat plate work looks authentic, l think it's had better rough cast look from the brush stippling before he added the putty coat.
Good idea on the weld , epoxy putty best as regular epoxy levels out again.
11 July, 12:55
Jakko
I've begun to add the weld seams now — see photo 23 🙂 Basically, Magic Sculp two-part epoxy putty that I mixed up a very small amount of, then took even smaller amounts from that and rolled it as thin as I could in my hand before pressing it into the join between the parts. Getting it to stick there is tricky, especially once I began texturing it with the tip of a knife — it wants to adhere to skin and steel much better than to plastic, unfortunately 🙁 But with a bit of perseverance it does eventually stick.
I've begun to add the weld seams now — see photo 23 🙂 Basically, Magic Sculp two-part epoxy putty that I mixed up a very small amount of, then took even smaller amounts from that and rolled it as thin as I could in my hand before pressing it into the join between the parts. Getting it to stick there is tricky, especially once I began texturing it with the tip of a knife — it wants to adhere to skin and steel much better than to plastic, unfortunately 🙁 But with a bit of perseverance it does eventually stick.
11 July, 17:41
Robert Podkoński
I see some heavy duty equipment here and a lot of elbow grease... Good job so far, Jakko! Keep it up!
I see some heavy duty equipment here and a lot of elbow grease... Good job so far, Jakko! Keep it up!
16 July, 15:17
Jakko
Thanks, though this is fairly straightforward. The most difficult part was finding a good way to curve the splash plates, really.
Thanks, though this is fairly straightforward. The most difficult part was finding a good way to curve the splash plates, really.
16 July, 17:21
Mr D
Taking shape now, the green welding joints are looking a better medium.
Interesting to see an adaptation taking place of the original.
Thanks for your posts, good to see steps
👍👍👍
Taking shape now, the green welding joints are looking a better medium.
Interesting to see an adaptation taking place of the original.
Thanks for your posts, good to see steps
👍👍👍
25 July, 21:06
Jakko
Thanks. TBH, I don't really care to look at photos of finished models — I much prefer seeing how they got to be that way, after which the finished pics make sense 🙂 So I post in-progress photos instead of only what it looks like at the end.
Thanks. TBH, I don't really care to look at photos of finished models — I much prefer seeing how they got to be that way, after which the finished pics make sense 🙂 So I post in-progress photos instead of only what it looks like at the end.
26 July, 08:57
EmilBerlin02
володіє цим предметом
володіє цим предметом
Aircraft Weapons: D U.S. Smart Bombs & Target Pods
Hasegawa 1:48
36008-1000 (X48-8) 2000 Нова прес-форма Багато тем (11)10 August, 20:30
Rona
додав новий фотоальбом.
додав новий фотоальбом.
37 26 December 2023, 19:44
KHOVI
володіє цим предметом
володіє цим предметом
World War II Aircraft of the Aces :
Vought F4U Corsair Special Edition - Ira 'Ike' Kepford Airfix 1:72
02090 1989 Нові деколі 10 August, 20:30
gorby
додав новий фотоальбом.
додав новий фотоальбом.
8 зображення
Another weird one. AEC Matador REME.Новий: 10 August, 14:13 1:76
The photo which started it all.
1 10 August, 14:12
Alex K
Another Gorby-licious small-scale "weird" (we wouldn't want you any other way) creation... Definitely in! 👍
Another Gorby-licious small-scale "weird" (we wouldn't want you any other way) creation... Definitely in! 👍
10 August, 15:13
gorby
Welcome to the show Alex and thanks very much. 🙂
The buildy bit is nearly complete so, as usual I'm playing catch-up with the report. Hopefully another update tomorrow. 🙂
Welcome to the show Alex and thanks very much. 🙂
The buildy bit is nearly complete so, as usual I'm playing catch-up with the report. Hopefully another update tomorrow. 🙂
10 August, 16:35
Flotoc83
володіє цим предметом
володіє цим предметом
Focke-Wulf Fw190 D-9 JV44 & Citroen 11CV Staff Car Set
Tamiya 1:48
25213 2023 Набір моделей Багато тем (2)10 August, 20:28
o_O o_O
додав новий фотоальбом.
додав новий фотоальбом.
29 зображення
ГАЗель NEXT (Lenmodel) Диорама "Инкассация" 1:43Новий: 10 August, 20:27 1:43
Проект: Gazelle NEXT
Scratchbuilt
3 23 June, 20:28
Stéphane Jayet
додав новий фотоальбом.
додав новий фотоальбом.
15 14 July, 16:30
Stéphane Jayet
Promising kit replacing glue by screw in many cases, but there are some moulding issue, so parts have to be well prepared.
Promising kit replacing glue by screw in many cases, but there are some moulding issue, so parts have to be well prepared.
16 July, 11:27
Stéphane Jayet
@george, during my vacations for 2 weeks I installed some books on it and it is now almost ok
@george, during my vacations for 2 weeks I installed some books on it and it is now almost ok
10 August, 14:59
Stephan Fässler
хоче цей предмет
хоче цей предмет
Aeronautica Imperialis
Adeptus Astartes Fire Raptor Gunship Squadron 2x Citadel Miniatures for Aeronautica Imperialis Games Workshop 8mm
500-43 2021 Нова прес-форма 10 August, 20:24
Flotoc83
розпочав цей предмет
розпочав цей предмет
Sd.Kfz. 251 (3-in-1) Sd.Kfz.251/21 Ausf. C, Sd.Kfz.251/7 Ausf. D, Sd.Kfz.251/1 Ausf. D
AFV Club 1:35
AF35S35 2008 Нові деталі 10 August, 20:22
/uk/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=uk
35
35
/uk/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo