Стрічка новин

Robert Podkoński
Wow! This is going to be a true masterpiece... Watching with pleasure and interest!

Martin Oostrom
Can't you strip the sprues as a whole of the paint? Dip them in a bath of paint stripper? Might be a whole lot easier than sanding each piece

bossy122
Most of the pieces are under carriage, so they're not that visible......but I stay awake at night knowing there are seams and that they must be eliminated! I think I botched the body paint job and I hadn't noticed on its original project. I just went over the lint - think HAIR - with 600 to 2000 and that took care of it. Mostly, I just thought it was funny that whomever I bought this kit from had gone to that much trouble to paint pieces ON the sprues with a brush, only to be done over with a rattlecan OFF the sprues.

Martin Oostrom
I feel your pain. I'm currently sanding tanks on a truck. Tanks that will never be seen, yet I've spent a few hours already on them.

bossy122
The TS4 German Grey isn't nearly dark enough for the dash. Or, the actual color of the dash should be black, but the instructions called out for German Grey......I dunno, Tamiya.

George Williams
Buy cheap pay twice.

Bozzer
Sometimes, it's easier to use a thin Sharpie, for knobs and buttons. It dries fast, so if you make a mistake, you can touch up, more or less, straight away. I also use a Sharpie for window rubbers, etc

Spanjaard
lots of work, but it is looking nice now.
i got this one accidentally in my stash for a very, very long time.....

Robert Podkoński
The next Salamander? Taking a seat!

S M
Welcome, podkon! 😄 I have plenty of Salamanders to be built XD

Jan Peters
Joining Robert for this feast

Skyhiker
What does that aqueous black surfacer 1000 thin down with? Isn't aqueous a water based paint? Does it work well as a primer or does it peel off like the acrylic "primers"?

S M
I haven't tried to thin it with water although it is promised to work. I could airbrush mr.surfacer 1000 without thinning with my old 0,4mm needle airbrush, but in case I want to thin it I use Mr.Hobby Color Thinner 400 (turqoise colored bottle). I think this works very well as a primer. It sticks and it can be smoothed with sand paper.

Alberto
Nice work so far, watching! I also use aqueous black surfacer. I thin it 50% with Tamiya's X20A, spray it with a 0.4 mm needle at 15-17 psi. It works a treat.

Robin (WhiteGlint)
👀

Nicolas
Joining.

J35J
Swedish markings, I'm in on this project!

Skyhiker
Thanks for the info on the surfacer. I'm looking for alternatives to using heavy chemicals, and hopefully this will be an answer.

S M
Welcome, mates! 😄 @Skyhiker I just tried and it seems you can thin aqueous surfacer with water. I didn't paint anything with it yet.

Jan Peters
Nice progress, love the what if Swedish markings

Thomas Kolb
I am all eyes! Very cool indeed! I was initially quite baffled with the Swedish markings, the "what-if" went over my head.

S M
Model is now ready!

Guy Rump
Some vehicles to add for photographing my WW2 aircraft. 🙂

Guy Rump
Made a start on the Ambulance first starting with the underside of the vehicle. 🙂

Guy Rump
Underside of the ambulance painted Vallejo Model Air black. 🙂

Many thanks mate for your interest and like Jan P. 👍

Guy Rump
Body added to chassis. 🙂

Guy Rump
Painted the outside with Vallejo Model Air Dark Earth. 🙂 Next is the inside of the ambulance. 🙂

Many thanks mates for your interest and likes RolfRolf & 1 other mate. 👍