News Feed
Thomas O'Eh
添加了一个新相册
添加了一个新相册
8 图片
WIP新的: 16 September, 19:35 1:72
Some detail added around the fenestron, made from Evergreen styrene and stretched sprue.
19 4 August, 19:21
Martin Oostrom
Dryfit the front window early in your build. I've heard rumours of a horrible fit near the engine intakes
Dryfit the front window early in your build. I've heard rumours of a horrible fit near the engine intakes
4 August, 20:01
Alexey Bykov
check the rotation of main blades. in kit is made wrong side.
good luck!
check the rotation of main blades. in kit is made wrong side.
good luck!
24 August, 09:35
Thomas O'Eh
thanks for the hint, Alexey. Will be tricky to fix this with the bent rotor blades. Have you seen any built where this was actually corrected?
thanks for the hint, Alexey. Will be tricky to fix this with the bent rotor blades. Have you seen any built where this was actually corrected?
25 August, 10:54
Alexey Bykov
i made it =) karopka.ru/forum/forum260/topic24215/
you can bend blades in oposite side.
i made it =) karopka.ru/forum/forum260/topic24215/
you can bend blades in oposite side.
27 August, 18:55
Gergő Takács
Thomas. I built this kit a few months ago. I used also lead as you mentioned. I squeezd it and choped it. I placed them under the cabinfloor and I put some inside of the dashboard cover also.
Thomas. I built this kit a few months ago. I used also lead as you mentioned. I squeezd it and choped it. I placed them under the cabinfloor and I put some inside of the dashboard cover also.
5 September, 13:48
Thomas O'Eh
Thanks for all your advice, in the meantime I have continued on the details in the rear section and addressing the issue with the bad fit of the front window.
Thanks for all your advice, in the meantime I have continued on the details in the rear section and addressing the issue with the bad fit of the front window.
16 September, 19:35
Ferenc Sarka
Following. I started the same kit last week. It will be a difficult one.
Good luck!
Following. I started the same kit last week. It will be a difficult one.
Good luck!
16 September, 20:28
Aaron Konz
想要这件
想要这件
F-16AM Fighting Falcon J-015 "Solo Display Team 2009" Royal Netherlands Air Force
Syhart (Syh@rt) 1:48
48-055 16 September, 20:28
Jarda Malý
添加了一个新相册
添加了一个新相册
11 10 September, 19:46
Alec K
Nice Ferrari, taking a seat. Není Laudova a ani z papíru, ale to určitě nevadí 😉👍
Nice Ferrari, taking a seat. Není Laudova a ani z papíru, ale to určitě nevadí 😉👍
11 September, 13:32
Jarda Malý
Laudovu mám ještě v zásobě, tohle je zatím rozcvička. Uvidíme jak to dopadne, obtisky jsou po těch letech na hovno a taky lesklá červená bude sranda😀
Laudovu mám ještě v zásobě, tohle je zatím rozcvička. Uvidíme jak to dopadne, obtisky jsou po těch letech na hovno a taky lesklá červená bude sranda😀
11 September, 16:11
Alec K
Aha, tak to je správné 😂👍. Já auto nikdy nezkusil ale pro ty formule mám slabost. Ne tu červenou držím palce a těším se na pokračování. Motor je malej skvost 👍
Aha, tak to je správné 😂👍. Já auto nikdy nezkusil ale pro ty formule mám slabost. Ne tu červenou držím palce a těším se na pokračování. Motor je malej skvost 👍
12 September, 12:09
Jarda Malý
Alec K: díky. Ten motor bude nakonec zavřenej, nebude z něj nic vidět. Všecko je to jen pro ten pocit že to tam je😀 ale i tak natahám ještě pár káblíků.
Alec K: díky. Ten motor bude nakonec zavřenej, nebude z něj nic vidět. Všecko je to jen pro ten pocit že to tam je😀 ale i tak natahám ještě pár káblíků.
13 September, 04:12
Tom B.
添加了一个新相册
添加了一个新相册
4 图片
Alkett Vs.Kfz. 617 [TAKOM, 1:72]新的: 16 September, 20:22 1:72
The basic build is finished... only some textures have been added as well as some minimal stowage at the rear
16 September, 20:22
Los Kelly
添加了一个新相册
添加了一个新相册
24 13 May 2021, 16:27
Tom B.
Looks like it is going to be a very detailed build 👍 Can´t wait to see this continue!
Looks like it is going to be a very detailed build 👍 Can´t wait to see this continue!
22 July 2022, 11:35
tjsport2k
拥有此物
拥有此物
Cavalier F-51D Mustang/Mustang Mk.2 Conversion set for Tamiya kit
Halberd Models 1:32
unknown 2021 新模具 16 September, 20:21
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=zh
35
35
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo