News Feed

Ludvík Kružík
I still miss this small helicopter in my collection of flying machines used in Czechoslovakia. The time has come for me to rectify that. 😉

Villiers de Vos
I will follow along.

Ludvík Kružík
Welcome Villiers! 🙂

Greg Baker
Oh. I built a 1/72 version of the Mi-1M... This should be interesting.

Ludvík Kružík
Hello, Greg. I know there's a Mi-1M kit in 1/72nd scale. Unfortunately, only this and a rather old kit from Special Hobby exists in 1/48 scale. In addition, this kit is an older version of the Mi-1A, which is different from the upgraded version of the Mi-1M. It has a different nose shape, different cockpit glazing and other minor changes. And since I decided to build the upgraded version of the Mi-1M, I will not avoid modifications to the kit.
To give you a better idea of the extent of the modifications to the kit, I've included a picture with the differences between the Mi-1A and Mi-1M versions color coded.

Greg Baker
Oh, neat! I didn't realize there were so many changes between the versions. This is going to look great!

Ludvík Kružík
Greg, thank you for your support.
____________________
I started building the model by making new transparent parts.

Alec K
Taking a seat, this brings back memories of ABC magazine 😜👍

gorby
Nice work moulding the new transparent parts.

Greg Baker
Yeah. Nice work on the heat-n-smash moulding for the clear parts. That can be tricky to do.

Ludvík Kružík
@Alec K
I used to buy ABC magazine regularly as a kid and eagerly awaited each new issue 🙂. I assume your mention of ABC magazine refers to the occasional modeling tutorial section.

@gorby, @Greg Baker
It's not too difficult to make new transparent parts by stretching warmed transparent foil over a pre-made template. Preparing the template is the most work. Stretching the warmed foil onto the template is just a routine that anyone can do after a few attempts.

Alec K
Correct 🙂👍👍

Robert Podkoński
How have I missed this? Taking a seat for sure! 🙂

Ludvík Kružík
Hello, Robert! Good to see you here. You haven't missed much so far. Up to this point I've been more concerned with preparation than building the model.

Ludvík Kružík
I want to try to use the sandwich construction in the production of new glass parts for the coptics. So I made (using the same process as the transparent parts) parts out of white plastic sheeting. These parts will have holes cut out for the windows. The transparent part will then be inserted between these two parts. The white outer and inner parts will form the embossed framing of the transparent part.

Jennifer Franklin
That looks great (as per usual 😛)

Ludvík Kružík
Welcome, Jennifer, we're glad to have you on board and thank you for your goodwill. 🙂

Ludvík Kružík
I came back from vacation and it started to rain. Ideal conditions for modelling. 🙂

So I'm back and continuing to work on the model. I need to glue the finished nose to the glued fuselage so the cockpit overlay fits exactly. That determines the workflow. First I have to finish the nose and the inside of the fuselage and glue all the parts that need to be glued to the fuselage halves from the inside. After gluing the fuselage halves together, I would no longer be able to get to these parts (or only with great difficulty).

Photos of the work progress will be coming soon.

Alexander Grivonev
Oh some modeling for big boys, not glueing perfectly fitting parts together and throwing on some paint! Following 👍

Ludvík Kružík
Welcome, Alexander! 🙂

Ludvík Kružík
I glued several parts to both halves of the fuselage. These parts are glued from the inside, so they have to be glued before the fuselage is closed.
I also started working on making new parts for the cockpit.

Landlubber Mike
Wow, this is incredible work Ludvik! Thank you for sharing your steps - I've learned a lot from your pictures and descriptions!

Villiers de Vos
Fantastic scratch build skills.

Ludvík Kružík
@Landlubber Mike
Mike, thank you for your interest. Welcome aboard!
I've had the idea for this rebuild in my head for a few years now. Mainly because I've been waiting to see if anyone would start making 1:48 scale Mi-1M kits. Unfortunately, to this day, no manufacturer has this kit in their lineup. So I decided not to wait any longer and start building a model from what I have available.
My rebuild is just beginning. Most of the work on the model is yet to be done. I'd also like to try some new techniques that came to mind while planning to build this model.

@Villiers
Thank you for the compliment. I appreciate it very much.

Ludvík Kružík
I didn't have much time today, so I didn't make much progress on the build. But every little bit of progress counts. 😉

J35J
Great progress and detailing! Following

Bruce Huxtable
Wow! You don't shy away from challenges! Watchinh with admiration, and hoping to learn lots too. Hoping you are not amongst the floods? Stay safe!

Ludvík Kružík
J35J welcome! I hope you like it here.

Bruce, I like a challenge like that. I like to experiment and enjoy thinking of and then implementing ways to improve my model.

I appreciate your concern for my safety. I live in a town in the highlands that wasn't badly affected by the floods. Only the river that runs through our town has increased flow, but it hasn't spilled out of its bed. Moreover, our house is 80 metres above the river, so even if the river had spilled out of its bed, it would certainly not have reached our house.

Bruce Huxtable
It sounds an idyllic location.....Opravdu, česka příroda je krasná....

Ludvík Kružík
Bruce, thank you for the compliment. I'm sure the nature is beautiful in England too. 😉

Ludvík Kružík
I'm slowly continuing to make small parts.

Alec K
Nice progress, this will be a beauty 👍

Augie
Really good work an very interesting to look at.

Maier82
Bausatz wäre noch zu verkaufen. Gruß Markus

Harald A.
Nehme ihn sehr gerne, zu welchen Bedingungen verschickst du? Bin zwar in Österreich, habe aber auch eine Adresse in Deutschland.

Maier82
Versende mit DHL

Nach Österreich 13€
In Deutschland 7€

Harald A.
Bezahlung per Paypal?

Maier82
Ja PayPal würde gehen

Karljun@aol.com

Karl-Markus Rauchenecker

Harald A.
super, dann Versand in Deutschland, hab dir 29 Euro angewiesen.
Versandadresse ist:
Petra Angerer
D A Packs 2062158
Am Rain 53
Kiefersfelden, Bayern 83088
Deutschland

Maier82
Ist die Adresse eine Packstation von DHL?

Maier82
Wo in Österreich leben Sie ?

Harald A.
ja genau ist eine Packstation. Wir leben in Tirol, Raum Kitzbühel und meine Frau arbeitet direkt an der Grenze

Maier82
Ich bräuchte bitte noch

Postnummer des Empfängers

Packstationsnummer

Harald A.
Die Kundennummer ist die 2062158 die schon in der gesendeten Adresse steht, mehr ist da nicht notwendig

Harald A.
Lieferung ist angekommen, konnte sie aber erst heute abholen. Vielen Dank für den zuverlässigen Versand

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Spanjaard
nice details 🙂

Villiers de Vos
A classic. Nice progress.

Stephen Lesley
Thank you Spanjaard and Villiers. Yes, a classic indeed, but as always with a few issues. As the saying goes "some days a diamond , some days a stone". Today was a stone...

Spanjaard
classic indeed, i have a very similar project inventory, so really interested in the issues you may find 😉

Stephen Lesley
The issues I found were with the lower hull and the rear panel. These have to be carefully lined up or it can affect the fit with the upper hull. The turret was slightly warped which affected the fit with the turret ring and how it sits on top of the hull. The most annoying issue so far is the fitting of the side skirt brackets to the frame and the frame to the hull. The sprue gates for the brackets are on the mating surface so if you don't file them perfectly flat, they are out of line. And in a complete brain fart on behalf of Tamiya they designed the kit in such a way that if you attach all the tool racks etc on the the right hand side of the hull using the mounting holes, it prevents you attaching the side skirt frame properly, because the tools end up too low on the hull side. In the end I had to break off the jack block and some of the tool clamps to make the frame fit on the side. Not happy!

Spanjaard
thanks for all the info!