News Feed
Pantelis Antonoglou
添加了一个新相册
添加了一个新相册
45 29 November 2023, 19:34
Giorgos
Also watching!
I am curious to see your choice for the level of weathering 🙂 So far all the photos of the HAF Rafales show them rather clean 🙂
Also watching!
I am curious to see your choice for the level of weathering 🙂 So far all the photos of the HAF Rafales show them rather clean 🙂
23 April, 18:28
tyu
Looking forward seeing this build as I have several of your project aftermarket bits too. It seems a lot of blending of the BAM parts is required, correct?
Looking forward seeing this build as I have several of your project aftermarket bits too. It seems a lot of blending of the BAM parts is required, correct?
1 May, 14:07
Patrick Hagelstein
Nice color! 👍 Is it correct that Greece opted for a darker shade of grey than the original French color?
Nice color! 👍 Is it correct that Greece opted for a darker shade of grey than the original French color?
1 May, 14:17
Pantelis Antonoglou
Thank you gentlemen for your kind words. For a HAF Rafale you need almost all the BAM resins like the vents on the vertical fin, new wingtip mica launchers, new HUD, some extra RAM panels, replace the engine intakes etc. The grey camo is really confusing due to dramatic changes according the lighting. So in order to be "correct" i did my own mix of XF-54 Dark Sea Grey with H-308 in 70:30 respectively. You can use also MRP-279 (FS36293)
Thank you gentlemen for your kind words. For a HAF Rafale you need almost all the BAM resins like the vents on the vertical fin, new wingtip mica launchers, new HUD, some extra RAM panels, replace the engine intakes etc. The grey camo is really confusing due to dramatic changes according the lighting. So in order to be "correct" i did my own mix of XF-54 Dark Sea Grey with H-308 in 70:30 respectively. You can use also MRP-279 (FS36293)
1 May, 21:35
Mathieu
添加了一个新相册
添加了一个新相册
31 19 May 2022, 10:41
Mathieu
Hi Guillaume, Villiers and Vincent! Thank you for your kind words mates! Very appreciated !
@Guillaume, seeing your past quality work, you should definitely try 1/32 models at some time!
Cheers
Hi Guillaume, Villiers and Vincent! Thank you for your kind words mates! Very appreciated !
@Guillaume, seeing your past quality work, you should definitely try 1/32 models at some time!
Cheers
19 May 2022, 20:03
Mathieu
Guy, Gary, Neuling & Rui! Thanks a lot for your kind words! Being finally able to put an album on theses P-40 builds restarted the warhawk fire burning inside, there are 2 teethed birds back on the bench. More in the appropriate album.
Cheers
Guy, Gary, Neuling & Rui! Thanks a lot for your kind words! Being finally able to put an album on theses P-40 builds restarted the warhawk fire burning inside, there are 2 teethed birds back on the bench. More in the appropriate album.
Cheers
23 May 2022, 18:29
Paul Moore
Looking at this, it makes me reconsider buying the GWH P-40 when I can buy this kit for $40. But then again, I don't have your skills. Beautiful model!
Looking at this, it makes me reconsider buying the GWH P-40 when I can buy this kit for $40. But then again, I don't have your skills. Beautiful model!
3 July, 10:33
Treehugger
Hrm, I have this Iwata HP-CS Eclipse 0.35 airbrush and I am stressing a little when trying to airbrush on some camo (without masking). I didn't want to use masking tape and I don't have any camo goo to spread over as masking either.
Like with my other attempt with this other tank I think I have to airbrush on desert yellow over the darker colors and try correct the shapes of the camo. The big part on the side and the wheels arent' glued on.
I've never done this before (I used masking tape the last time I worked on a tank), I think I have to make sure the Vallejo Air paint is thin, and then try lower the psi way below 20 psi and try get close to get a crisp line when airbrushing. And I don't want to take off my needle guard to get closer, as I don't want to bend the needle tip, again. 🙂
I didn't want to make a WIP album for this, just another side project.
[img1]
Like with my other attempt with this other tank I think I have to airbrush on desert yellow over the darker colors and try correct the shapes of the camo. The big part on the side and the wheels arent' glued on.
I've never done this before (I used masking tape the last time I worked on a tank), I think I have to make sure the Vallejo Air paint is thin, and then try lower the psi way below 20 psi and try get close to get a crisp line when airbrushing. And I don't want to take off my needle guard to get closer, as I don't want to bend the needle tip, again. 🙂
I didn't want to make a WIP album for this, just another side project.
[img1]
3 July, 12:13
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=zh
35
35
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo