News Feed

Zbynek Honzik
Taking a seat and I keep my fingers crossed that the building will be joyful and successful, Michael!

Mr D
Really like the subject 😁👍👍 Good stuff, l built one as a boy in the 1990's

Łukasz Gliński
Can't miss an IF project 👍
That windshield is terrible - what's your plan for it?
And most importantly - are you going to build Lady Agnes? 🙂

Michael Kohl
Hi mates. Nice to have your interest and you on board. Thanks Zbynek. So far it took much more effort than I expected. Lets see how it continues.
@Mr D: childhood memories. I suppose you build it in scale 1:100? VEB Plasticard?
Lukasz, I bent and glued it und sanded it flush afterwards. As I will use the Authentic Airliner decals for the cockpit windows, they do not need to be transparent.

Mr D
Hi Michael 👋,
Yes it was the Veb version, very basic....but l was enjoying building it as fast as l could.... Glue finger prints n all 🤣
Can you sort the cockpit glass ?? Surprised.... Zvezda usually very good.
Thanks for your upload..... I'm big Soviet era fan.

Łukasz Gliński
Good choice Sir, the AA window decals are super cool.
Unfortunately some of their livery decals have some errors.

Michael Kohl
Yeah, I was surprised by the fit issue too. On the upside are definitely very fine and consistent engravings which I hope to preserve.
And - by the way - it won't be Lady Agnes¹. I like to represent the plane I flew to Moscow with. Unfortunately I do not have a picture of this particular aircraft and am thus not sure about it's actual registration. The history of some a/c is available to me, so I can rule out some. And I photographed two parked IL-62M too while taxiing which I can rule out too.
With these informations I ruled out registration: SEW, SEC, SEF, SEG, SEY and SEK. So right now I will go for registration DDR-SET.

¹ a word for those not familiar with Lady Agnes. She is obviously an IL-62M too and was flown to Stölln. After being stripped of everything unnecessary she landed on a 900m grasstrip (how on earth did they manage to get a permission for that?!) and is used now as a Cafe there in it's original Interflug livery.
You've never heard of Stölln? It is located in the federal state of Brandenburg, about 40km west of Berlin and is the oldest aviation site on earth and in the history of mankind. No other that Otto Lilienthal tested some of his gliders there.

Robert Podkoński
Watchimg with pleasure! Of course, I remember VEB Plasticard kit very well 😉 And thanks for the interesting story!

bughunter
Oh, a very personal project - watching! Sorry, I digged so deep into my build that I missed yours.
So I'm now in and good luck!
Regarding putty: I'm now a fan of Tamiya light curing putty which hardens quickly with UV light.
If wee meet again I like to hear more background about this trip and can provide other insights 😉

Michael Kohl
Hi Frank. No reason for apologies. You are welcome anytime.
Looking forward to our next meeting.

Spanjaard
a bit late, but I am in. nice detail added in this intakes

Ben M
💺

Mr D
Looking good, really nice shaped Airliner 👍
Do you use the black to find imperfections?? Or is it a pre-shading??
I'm in process of building the Veb Be-6 Soviet flying boat, and may help me to do similar.
Thanks for your uploads... Like anything from Soviet era n russian.

Bozzer
I'm glad to see, that it's not just me, who does all this type of prep work. I've spent far too much time and money, on tools, gizmo's and fabrication of various things, just to try and speed up this process. Yet, I still end up falling back to the back of a #11 knife blade!
I'll hang around for this one mate, mainly to see the outcome of those amazing decals. But also to watch how the trailer goes together?
I helped my son build the Spacecab, way back in the early 2000's. He didn't enjoy it and abandoned his efforts 🙁 No wonder he became a plumber 😛

Martin Oostrom
Kerry Cox taught Peter Hardy and Peter taught me: "Better remove those lines, you'll always know they're there."
I mostly use the cutting edge of the blade to scrape, I'll try the back sometime.
I assembled the chassis today and it seems perfectly straight. A lot of work remains before I can start on the decals.

Bozzer
If you draw the edge, of the back of the blade, it gives you a nice smooth, flat surface. It also doesn't dull your sharp blade? After a while, it becomes second nature. I have found, that those nasty mold lines, show up even more, when paint is applied? Even when I glue two parts together, it's always the back of the knife, that deals with the seam. You should definitely try it, and see if you notice the difference.

Lode Schildermans
Following. Martin and trucks and trailers, always surprising

Bozzer
He's got this, Lode. Martin is the Plastic Surgeon 😉

Spanjaard
I am in 🙂

Martin Oostrom
The doctor is in 😄
I managed some work on the axles Tuesday evening and I had half a day to myself yesterday. So I built the box with a lot of added plastic to get everything squared. I'll be sanding the outside and I don't want the thing to fold.
The mudflaps were unconvincing , so I went to town on them. Your opinions please?

Bozzer
I've heard of guys, filling in reefers, with expanding foam?
I've never personally done it, because I like the option of opening doors. Those mudflaps look so much better now, too.

Martin Oostrom
Mmm, insulation foam in a reefer….
There is/was a load of cyanide in that stuff. Not something I want to emit in my hobby room.
My 2k also contains cyanide, but those vapours are mainly vented outside

Bozzer
I have never checked mate, and I've used it for sealing gaps, etc, for decades? However, I've definitely not used it on any models. In fairness though, all my current reefers are from AMT. I love the fact that they use 1 piece plastic, for the sides, base and top. It definitely makes them sturdy. I do have a few Italeri reefers though, and I was thinking about lining them with thin plastic? I don't want to compromise the look, so I thought maybe some 1mm sheet, would work? What do you think mate?

Martin Oostrom
Lining with 1mm sheet is a possibility, but … see my new picture. On both sides there are two half rods running the whole length of the trailer and the ceiling is littered with protruding ejection marks.
The floor is smooth as the ejection marks are on the underside.
This Revell edition has water slide decals, the Italeri reefer I have has two big stickers for each side. Will be hell to line up, so I'll probably paint something.

Bozzer
On large decals, it's best to cut them into 3. It just makes things easier. I honestly wouldn't have a clue what to do with stickers though? That's exactly what I have, on my Smokey and the Bandit 2 trailer.
Which reminds me...
Jerry from Modeltruckin, is retiring. Last orders are being taken upto end of July. Get them decals ordered mate, before you can't get them again!

Bozzer
I just took a closer look at your pictures. I see those rails now. I'm guessing that they were a feature, to stop pallets from ramming up tight to the side, on the 1:1 version? The injection pin marks, I can Dremel away. You've actually got me thinking about digging out one of my reefers now, lol

Martin Oostrom
In the real one, there will be a strip with slits to secure the cargo. But those are generally not that high and low. See picture.

Bill Newcomer
Late to the party. (I have been really busy with my wife's garden and my 1:1 car) Following. Making your box square and straight looks like quite the endeavor.

Martin Oostrom
Dry fitting the door showed a small gap between them. I later added a strip of styrene to the back. Stiffening the doors by accident.
I removed the moulded rear lights, only realising too late that they're hollow. A thin sheet of styrene helped. I also glued a strip to the storage bins. Too much sanding otherwise. Now all trailer parts are ready for painting.

Lode Schildermans
Definitely impressed, Martin. Smart building by improving stability in the beginning of the build. I particularly like the improvements with styrene

Martin Oostrom
Don't tell anybody Lode. There'll be some pe on it. 🤫

Bozzer
I wonder if that PE is going to be the bars and locking system, for the back doors?

Lode Schildermans
I shall be silent as a grave, Martin

Martin Oostrom
Wait and see Bozzer!

Bozzer
Oh Martin, you tease! 😛

Martin Oostrom
Primer's on! It took over 4 hours to paint the truck and trailer in my tiny booth.

Lode Schildermans
But the result is a success. Looking forward to see your progress of this big one

Gerald
👍

Martin Oostrom
First colours are here. Tamiya bright red, Tamiya silver and not shown, Tamiya aluminium straight from the can on the reefer itself.

Bozzer
Excellent colour choices, mate. This build is exciting me 😄

Bill Newcomer
Color, Always good to see color. 🙂

Martin Oostrom
For the first time in forever I follow the colour callouts from the instructions, and now my choices are excellent. Makes me wonder…
Enjoy the colours while you can, this thing will be wrapped in decals when she's done.

Bozzer
Lol, maybe because it's more true to life?
Although I have to admit, I've crawled under a few trailers, and they were all the same, light rust/brown colour. Even on fleet management, the chassis and underneath, never get washed. I do a lot of work for a global logistics company and their trucks always look clean, but they're not. My brother works for a national retailer, driving big rigs. I asked him when he washes the underside of his trailer? His answer was priceless, but unfortunately, unprintable 😉

Martin Oostrom
I actually had red oxide primer in mind for the red parts, but didn't at the last moment!
I also never wash the underside of my car. And I've worked in port, so I can imagine some colourful language.

Done with airbrushing for now. Only some detail painting to do.
And after curing, it's decals time!

Goldman
Good luck with these decals. Hope the decal spray will do its magic.

Spanjaard
fingers crossed

Bozzer
Mate, please do as Goldman suggested on your other thread, and take pictures of these?
It's definitely worth a try? I can't bear to hear the screams, if the decals spray doesn't work.
We need you to be successful on this, to raise the bar, and give the rest of us, something to reach for?
God speed, my friend, and good luck 👍