News Feed
HyunMo Koo
拥有此物
拥有此物
Master Grade
RB-79 Mobile Pod Ball Ver.Ka Middle-Range Support Type Bandai Spirits 1:100
5063542 (0131412) 2022 新的盒子 12 October, 03:25
Eric
开始了此项目
开始了此项目
High Grade (HG)
LM314V23/24 Victory Two Assault Buster Gundam League Militaire Multiple Mobile Suit Bandai 1:144
0196527 (189) 2015 新零件 12 October, 03:22
David Formosa-Kerr
将此物品标记为
将此物品标记为
Multi-Role Combat Aircraft (M.R.C.A.) Europe's Swing-Wing Strike Aeroplane
Airfix 1:72
04019-6 1975 新模具 12 October, 03:18
Bozzer
添加了一个新相册
添加了一个新相册
6 11 August, 08:01
Bozzer
I'll get some more pictures up, later today, but basically this is something that I've always wanted and finally got the chance to have.
I printed this myself, after purchasing the files. I have to admit, these are bloody amazing files. I had a few hiccups during printing, and this was narrowed down to a corrupt flash drive. I can't wait to get this one done and on the shelf.
I'll get some more pictures up, later today, but basically this is something that I've always wanted and finally got the chance to have.
I printed this myself, after purchasing the files. I have to admit, these are bloody amazing files. I had a few hiccups during printing, and this was narrowed down to a corrupt flash drive. I can't wait to get this one done and on the shelf.
11 August, 08:07
Bozzer
I shall, Martin. Just need to get back in the cave and take some. I can tell you that the chassis is very good. It lines up almost flawless.
I shall, Martin. Just need to get back in the cave and take some. I can tell you that the chassis is very good. It lines up almost flawless.
2 October, 07:45
Bozzer
@martin. I bought some ABS-like, transparent resin, so I could use it for clear parts. What you see is, 2mm thick clear. I've not tried it any thinner, but for my taste, it's not good enough to use as glass for cab windows, etc? However, I'll give it a try, soon, just for a sample. Even i can be wrong, sometimes?
@martin. I bought some ABS-like, transparent resin, so I could use it for clear parts. What you see is, 2mm thick clear. I've not tried it any thinner, but for my taste, it's not good enough to use as glass for cab windows, etc? However, I'll give it a try, soon, just for a sample. Even i can be wrong, sometimes?
5 October, 23:24
Martin Oostrom
You're not wrong, you tried something new that didn't work out as hoped. No shame in that!
You're not wrong, you tried something new that didn't work out as hoped. No shame in that!
6 October, 07:16
Nigel Chapman
How have I missed this?
Wow Bozzer that is awesome. I agree with Martin it does look strange in that colour. At first glance I thought it was bread dough!
How have I missed this?
Wow Bozzer that is awesome. I agree with Martin it does look strange in that colour. At first glance I thought it was bread dough!
6 October, 08:34
Bozzer
The original mistake was how I orientated the print. Also, I cured it in my machine. On the second attempt, I cured it slowly by sunlight and started assembly before it was fully cured. That turned out better, because I was able to get a better joint and the Super Glue held it better. Still a little filling, but a much better result. My plan is to light sand everywhere, then apply a filler/primer. I need to source this, but I will.
You boys will appreciate this....
The wife walked into the new cave, and stopped talking!
She's now aware of the stash that I've accumulated, during her absence. She said that I must have spent a lot, on kits?
I told her that they're cheaper than hookers!
When the swelling goes down, from my black eyes, I'll start modelling again!
The original mistake was how I orientated the print. Also, I cured it in my machine. On the second attempt, I cured it slowly by sunlight and started assembly before it was fully cured. That turned out better, because I was able to get a better joint and the Super Glue held it better. Still a little filling, but a much better result. My plan is to light sand everywhere, then apply a filler/primer. I need to source this, but I will.
You boys will appreciate this....
The wife walked into the new cave, and stopped talking!
She's now aware of the stash that I've accumulated, during her absence. She said that I must have spent a lot, on kits?
I told her that they're cheaper than hookers!
When the swelling goes down, from my black eyes, I'll start modelling again!
6 October, 16:24
Mr D
Looking great 👍
What is it made from??
I've never come across a build like this??
Looking great 👍
What is it made from??
I've never come across a build like this??
6 October, 18:44
Nigel Chapman
Taken out of context 'starting modelling again' doesn't sound much better 🤪
Taken out of context 'starting modelling again' doesn't sound much better 🤪
6 October, 22:57
Bozzer
Lol, she was cool with it really.
@Mr D. This is an ABS-like, clear resin and printed on a resin printer. It's the largest resin build, I've done, to date.
Lol, she was cool with it really.
@Mr D. This is an ABS-like, clear resin and printed on a resin printer. It's the largest resin build, I've done, to date.
7 October, 17:10
Mr D
Thanks Bozzer, learned something new.
Looks a fun project, all the best with it 👍👍
Thanks Bozzer, learned something new.
Looks a fun project, all the best with it 👍👍
7 October, 19:06
Bill Newcomer
I have been out of the loop as my summer has been very busy. I shall be very interested how this comes along. I can afford a 3D printer, I simply do not have the space for one.
I have been out of the loop as my summer has been very busy. I shall be very interested how this comes along. I can afford a 3D printer, I simply do not have the space for one.
12 October, 02:34
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=zh
35
35
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo