News Feed

Олег О
how beautiful

André Knippenberg
Great build!!

George Williams
Looking great so far.

George Williams
Looking great so far.

George Williams
The decals look really good.

Christian W
Damned, how far will I go? Found a quite interessting wip on modelcarsmag (modelcarsmag.com/for..-mpc-72-pontiac-gto/) with a lot of work on the fitting ...

István Szücs
Christian, that's an incredible build!

Martin Oostrom
I'm not sure I like the front end of that car.
Let's see what you'll make of it

Christian W
The front end was an issue ever. Im not the biggest fan too. I was buying this because I thought it was built in 1973 too. But the 1973 GTO is a totally other car and this kit doesn't fullfill the requirements of our annual group build of our "club".
After looking through that wip, ... I think I will not go that far. But one I will do: reduce the gaps at the front. They are really present.

Christian W
I started this GTO in between because the Charger sucks a little or my mind gives me the order that I have to work on several kits at the same time.
I was in the mood, to get this car painted. So I get some spots sanden on the body, fillered it and gave it a kind of green-turquis-blueish. This rattle can is on of the leftover of the 1977 Firebird (1977 Pontiac Firebird Coupe | Project by christian-w (1:25)) color I bought, when I was looking for the right color. I think it works on this car good.

Christian W
By the way: I'm not going for a vinyl roof on that.

Christian W
Next steps are done. The body got it's clear cote, undercarriage and interior is painted too. It's good. Now I'm thinking about how to get a little more shade into the interior color. It's to close to the body color.

Martin Oostrom
Spray some Tamiya smoke over it?

Christian W
Smart idea! Maybe this klear yellow from Tamiya could work too. I have to give that a try.

Christian W
I painted the interior. First i tried with tamiya smoke to go over it but I wasn't satisfied. Then I went through my metallic paints and grabbed #397 (Car Metallic Plane Tree Green) and mixed a little #60 (Yellow Green) into it. Maybe 10%. I think it's not that bad so far.
Now I think about to take the same mixture for my 1977 Firebird 🙂

Martin Oostrom
Nice colour for the interior

Christian W
Thank you! It could be, that I go over it another time. It depends on, how it works together with the exterior color. It might be a little to green 😉 The body looks more blueish. Darker. Dirtier 😉 Somehow.

Christian W
Did the interior. I think it's ready to be completed

Bill Newcomer
I like your build. It may be too late now, but the rear package tray was this cardboard and is the same color as the door cards.

Christian W
Thanks, Bill. Maybe to late. Yes, it is. I know, that it should be in the same color like the door panels and/or the seats. I wanted to have a bit of more contrast in the interior because it looked a little boring for me I will say. So I decided, to "costumize" that. I was thinking the same way at the lower part of the door panels too but - as you can see - I didn't change that.

Nigel Chapman
Love that interior

Christian W
Thank you verymuch. The last week I took the chassis and powertrain. It comes to an end. Taking pictures and get you an update. I decided too, to build a mold for the lights to get them clear instead of that chrome at the front.
With this kit I'm fine.

Christian W
I finally started this thing.

István Szücs
I'm curious for the final result!

Christian W
Me too 😉 I think I'm going on with that hood. The chances to get the right on ist nearly Zero.

Chris Parsons
Aah….been there, done that. I know your pain young Jedi!
I had the original as well at one time, re-powered with a 68 440 six pack, never going back to build another real "muscle car" but nice to have a representation of it at the least.
I converted the AMT 1971 body to a 73/74 body (it's a much cleaner mold) but used parts from Revell/ Monogram B body kits to get there in the end…musta used at least 4 other kits for parts. Scariest part was changing the rear side windows shapes from sweeping up to sweeping down. I may have pictures here somewhere…not sure but, I'm pretty sure I posted the build thread on Britmodeller if your interested

Christian W
@Chris ... That was my first thought when I read the first sentences, where you wrote that you converted the 1971 into that: the small window at the side and the c-post. I'll do a research on britmodeller to see, what you've done. On that point, it is too much work for me to go such a way. I want do have the kit done in December. I know, the details "under the body" could be better, but when it sits in the shelf, it doesn't matter somehow. For my needs, it is ok. It's only the hood, what concerns me for accuracy with the look to the movie car.

Christian W
@Chris ... I found your thread. But sadly there are no pictures anymore.
britmodeller.com/for..ger/#comment-3826045

Chris Parsons
Oh crap!
Sorry

Christian W
No problem 😉

Chris Parsons
I've found and added some images of my finished model here, no longer have images of the w.i.p. No idea what happened to them, you may be able to use (or not) for your build. The images are in my "Albums"

Bill Newcomer
I shall follow too.

Chris Parsons
That's nasty! I've had a paint do that to me as well! Never a good time!

Martin Oostrom
Tough luck Christian.

Bill Newcomer
I have never seen hobby paint crack like that. What is the carrier, enamel, lacquer, water?

Bob Hall
I thought it was cat hair at first glance and I was going to suggest, it time to shave the cat, but I see it's more of a deep rooted issue ! 🤔

Christian W
Thanks for your comments. First when I came into my hobby room I also thought it is a hair but... you see. I don't know, what went wrong. I used my rattle cans as on every model kit I built for years.
@Bill I don't know, what the colors are based on. As soon as I had no issue with them I didn't care.

The Dodge sits in a bath to get the paint of. After 24 hours the black was gone. Usually the primer stays on the body. In this case it was as usual 😄 but the hood is sticky and some parts of the body too. The crap goes on.

In the time of hoping and praying 😄 I took the bumper to get rid of that bumperettes.

Nigel Chapman
Is it a chemical reaction with the different paint colours?
Do you use the same paint manufacturer for your rattle cans?

Christian W
Maybe and no 😉
I do not know, whether it is a chemical reaction or something else. The manufacturer are different. I had the same issue with a
-> black Pontiac (easily 5 years ago - Pontiac Firebird - RIP | Album by Dominik (1:25)),
-> blue F40 (finished in 2017 - 1987 Ferrari F-40, Revell #7327 | Album by christian-w (1:24)) and
-> black Viper (Restoration in 2022). But the cracks came after some months or years and not within 24 hours.
-> KARR after
Now, when I'm writing this lines, I remember, that
-> another Pontiac got cracks in 2022 too (1989 Pontiac Firebird (red) for a friend - wip | Album by christian-w (1:25)).
The filler was the same but the body color was another manufacturer like on the Dodge. But the cracks came after clear cote. So ....

What do they have in common?
Filler? Yes. Only the Viper has old color under the new painting (it was a restoration - paint remover followed by a new paint job)
Color? Different manufacturer
Clear coat? Not all of them. Only KARR, the red Pontiac and F40.
Cracks came between 24 hours (Dodge), 9 months (red Pontiac) a couple years (F40). Also the time between the different layers vary or the question about a wet sanding and painting over it. There are a minimum of 2 days between the steps. Usually weeks, especially with clear coat.

I don't see a clear pattern.

shadowlight
Just some more thoughts about what do they have in common...
- moisture, temperature and air condition in your working room
- air pressure and paint thinner
I am very sorry that this happened to you btw.

Skyhiker
Not sure if this applies but cracks can happen if the under paint drys slower than the top coat. This can sometimes happen when you use a laquer or oil based paint and then add on top a faster drying acrylic or water based top coat that is too thick.

Christian W
Thank you for your suggestions.
@Skyhiker .... I think I can skip this reason mostly because. There were 9 days between base coat and the black. Before I painted it black, I wet sanded it and let it sit 2 days for drying. I think, that was enough time.
@shadowlight .... moisture and temperature could be a reason. Because I used my rattle cans for painting, I was outside. In this case in the evening hours and not middays. The day was sunny itself but when I painted it, the sun was nearly gone. Thanks! I'll keep that in mind.

Another little step done: removing the bumperetts.

Christian W
At the weekend I sanded a lot of the filler down. The surface should be smooth enough. Yesterday I did another try to get it black. This time I used ma airbrush to paint it. And I skipped another layer of base coat 😄 At this time I don't care. I just want to have the paintjob done.

Bozzer
Christian, I don't care what anyone says, picture 20 looks awesome, and I would've just rolled with that, and stuck it in a diorama of a kid, trying to fix it up. I doubt that I'd ever be able to get that look, and you nailed it by accident! I gotta admit though, that black looks nice 👍

Christian W
You've nailed it. That were my thoughts too. If the next try fails, then I'll go with a restoration project. I'm not a person who throws model kits into the trash.
Thank you for your lines.

Nigel Chapman
Christian, Your perseverance has paid off handsomely, that new paint job looks ace

Christian W
Thank you. Yesterday I took it but I didn't do anything with it. I'll go for another wetsanding job. Why? Hm. Stupidity is sometines an a-hole. When I brushed the underside of the hood, it went off of the "holder", flipped and landed with the freshly painted side on the ground of my paint booth. You can imagine, that tehre is still some dirt on the ground. So that dirt is now on the hood scoop. Lesson learned: keep the parts better on the "holder".
I guess, that I have to give it another layer of black before even thinking about doing the clear cote.

István Szücs
If it wouldn't be a movie car, I'd leave the body in semigloss black, it's very nice.

Christian W
I Know! It looks pretty good.
Yesterday I wet sanded it and it Looks good so far. Another paintjob will follow and then a clear cote. Hopefully it works.

George Williams
Hope it works out for you, Christian.

István Szücs
Christian: fingers crossed!

Christian W
Just for info: the Carger got a second layer of (satin) black. It looks good so far. Hoping, the clear cote turns out good.

Christian W
The next layer of clear cote came out good. This time I used 2K. It's good. Will to have a round of wet sanding and polishing.

Christian W
I'll say the interior is done. SO let's face the fact, that I have to lay hands on the body.

Chris Parsons
Very nice crisp clean work...well done

Dominik Weitzer
nice work on the interior 🙂

István Szücs
The white interior looks amazing with those wooden inserts! I only miss the flocking from the floor.

Christian W
Thank you very much.

@Istvan .... Maybe I'll pour a little powder in. I don't kno. It depends on that, how much will be visible when I put the body over it. I'll check that.

Christian W
I polished that thing but am not satisfied with the result on the roof and trunk. So I'm still undecided about what I'm going to do. The trend is towards another wet sanding and a new layer of clear coat.

Chris Parsons
You've inspired me to build another cha cha myself. Ya bugger!

Christian W
You're welcome 😉 I waited long for this built and it is a challenge for me. The paintjob at most.
Yesterday I put another layer of clear coat on it and I'm still not satisfied with it. Man....

Neuling
Beautiful models! They deserve more photos .........

Prieur Gaël
Thank Neuling, You will find more pictures on my club blog : airbusmaquetteclub.blogspot.com/
, there must be a post for each with several photos each time, except for the IIIB and IIIE where the posts are to come, will have to follow the blog 🙂

Neuling
Merci!

Alexander
Impressive collection of Mirages, look all very nice. 👍

Prieur Gaël
Thanks Alex

Marius
Very, very impressive album!

Sergej I
Oh wooow! 👍

Erik Leijdens
Great collection of Mirages! Well done!

Tom B.
Impressive lot of Deltas... and F.1s, of course 👍 Must be an impressive sight when line up in a display-cabinett!

Guillaume Blanchet
Superbe! J'amerias voir une photo ou on les voit toutes ensemble.

Michael Kohl
one nicer than the other and all well built.

Prieur Gaël
hello every body, thanks for your reply, I'm happy you enjoy my work.
Ah Guillaume je sais pas si ma table est assez grande... je dois avoir une photo d'une expo où il y a les onze F.1

Villiers de Vos
A very nice line-up.

Rui S
A beauty 👍

Neil
C'est magnifique!

Prieur Gaël
Thanks Neil

Guy Rump
Very impressive collection. 👍

Vincent
Great collection of one of the best looking fighters ever made.

Prieur Gaël
Thanks for your replies

Alex K
... and a nice Vautour! 👍

Treehugger
I take it that OP has already seen the movie "Sky Fighters"? 🙂

Prieur Gaël
the 5-OP especially saw iraq and saudi arabia with this camouflage

Pierre Pierre
une bien belle collection

Lost_Erik
An awesome collection. Bravo!

Skyhiker
Wow, am I seeing a mirage or what?

Roberto Rocat
What a nice collection! Beautiful machines, great builds.

Prieur Gaël
Grazie mille Roberto

Rui
Thanks for sharing! 🙏
It was a pleasure to look through so many Mirages 👍