News Feed
Sy Bar
添加了一个新相册
添加了一个新相册
18 September, 11:53
Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
18 September, 11:56
Stephen Lesley
添加了一个新相册
添加了一个新相册
25 图片
Tamiya Panther G late.新的: 18 September, 11:44 1:35
This is the tank I will be modelling. Early 1945 in Hungary.
22 14 July 2023, 07:28
Stephen Lesley
Thank you Spanjaard and Villiers. Yes, a classic indeed, but as always with a few issues. As the saying goes "some days a diamond , some days a stone". Today was a stone...
Thank you Spanjaard and Villiers. Yes, a classic indeed, but as always with a few issues. As the saying goes "some days a diamond , some days a stone". Today was a stone...
20 July 2023, 09:25
Spanjaard
classic indeed, i have a very similar project inventory, so really interested in the issues you may find 😉
classic indeed, i have a very similar project inventory, so really interested in the issues you may find 😉
20 July 2023, 11:26
Stephen Lesley
The issues I found were with the lower hull and the rear panel. These have to be carefully lined up or it can affect the fit with the upper hull. The turret was slightly warped which affected the fit with the turret ring and how it sits on top of the hull. The most annoying issue so far is the fitting of the side skirt brackets to the frame and the frame to the hull. The sprue gates for the brackets are on the mating surface so if you don't file them perfectly flat, they are out of line. And in a complete brain fart on behalf of Tamiya they designed the kit in such a way that if you attach all the tool racks etc on the the right hand side of the hull using the mounting holes, it prevents you attaching the side skirt frame properly, because the tools end up too low on the hull side. In the end I had to break off the jack block and some of the tool clamps to make the frame fit on the side. Not happy!
The issues I found were with the lower hull and the rear panel. These have to be carefully lined up or it can affect the fit with the upper hull. The turret was slightly warped which affected the fit with the turret ring and how it sits on top of the hull. The most annoying issue so far is the fitting of the side skirt brackets to the frame and the frame to the hull. The sprue gates for the brackets are on the mating surface so if you don't file them perfectly flat, they are out of line. And in a complete brain fart on behalf of Tamiya they designed the kit in such a way that if you attach all the tool racks etc on the the right hand side of the hull using the mounting holes, it prevents you attaching the side skirt frame properly, because the tools end up too low on the hull side. In the end I had to break off the jack block and some of the tool clamps to make the frame fit on the side. Not happy!
20 July 2023, 12:13
Cole
添加了一个新相册
添加了一个新相册
7 17 September, 08:23
Cole
It's not too bad, but when I enclose the interior, there is a need for quite a bit of trimming. I also need to add extra material to the top and bottom of the interior so the airframe sits flat at the bottom and marries up equally at the top. I'll add more photos when I'm up to that stage
It's not too bad, but when I enclose the interior, there is a need for quite a bit of trimming. I also need to add extra material to the top and bottom of the interior so the airframe sits flat at the bottom and marries up equally at the top. I'll add more photos when I'm up to that stage
18 September, 11:37
Aycee
添加了一个新相册
添加了一个新相册
1 18 September, 11:26
Stephen Fenech
拥有此物
拥有此物
SIAI Marchetti SF-260 Flying with Air Forces Around the World
Aircraft in Detail 货号: 016
Robert Pied, Nicolas Deboeck
2021 18 September, 11:29
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=zh
35
35
/zh/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo