News Feed

M0rce
Oh this is very nice. Loving the work on the crane and the ropes. Lots of great additions

M0rce
Nice stairs too

M0rce
Loving the funnels and the pulleys. Are they all scratchbuild? And those anchors? Scratchbor aftermarket? Excellent eork Sir!

Tcamp
Oh btw i wasnt digging " jackal" so i cut up 1/48 marines decals and she became " Marin" lol

Tcamp
Oh the funnels were 1/350 from liberty ship spares

Tcamp
Oh by the way thank you!

Tcamp
Sorry anchors if i remember are 1/350 scale

M0rce
Gret stuff.
Would love to.awe your other builds too

M0rce
Just noticed the little 🔔 so cool

Neuling
Well done!

Tcamp
Thank you

Guy Rump
Lovely job! 👍

Tcamp
Thank you guy

Gerald
Hello Welcome here 🙂

ModelKid
Thank you!

Desert Marlin
Bridge of Spies...

Doubtingmango
So I just finished this little Italian job. The decals came out with a lot of the edges showing, which then got a lot worse when I added some washes. I used Microset on the decals, and then sealed them with Tamiya semi-gloss before the washes, but it actually looks like the washes got under the decals. Any thoughts?

Bogicevic Vladimir
It looks like you haven't spray gloss coat before you applied decals. Or decals didn't set well. There are two solutions. One is lacquer thinner. Put the thinner with fine brush in dots over the place where you have silvering. Thinner should destroy the film. If it raises paint under, just leave it, it will settle back. Important thing here is that, once you applied thinner, you shouldn't touch decal for something like 20 minutes, at least. Second way is mix of sugar and water, half - half. You make a hole with a needle on the decal, than you put mix on the top. It should enter in the space between decal and paint and, when drayed, make a gloss film in between them which will act as a gloss under the decal. Wipe excess mix with wet cloath and you are done.

Mr James
How annoying. I've never heard of the sugar water trick from Bogicevic. I'll be interested if this works. If the thinner, sugar trick fails, what else can you do but use a scalpel to cut around them, since you've sealed it,

Mr James
Oh, nice paintjob by the way

Doubtingmango
Thanks mates! I believe Bogicevic is right. I think I did fail to gloss coat before the decals. I think I'll try the sugar water first

Bogicevic Vladimir
Ok. There are few small tings I should add then. Heat the water first, when hot it will disolve sugar beter and apply it while it's still warm, it will have more viscosity. Make small hole or slice with modeling knife, put few drops of mix on the top and let it dry. You will see emidiatly if it's penatrating. When dry, wipe carefully excess mix with moist cloth. Repeat where neaded. I know it sounds ridiculous, but it worked for me many times.

Doubtingmango
Thanks Bogicevic! I'll give it a shot. If it doesn't work I'll try the lacquer thinner technique. I love this site!

Mark Sherwood
Where the *uck's this been hiding. Very nice build Mr Mango and I hope the decal solution from Bogicevic work's out🤞

Doubtingmango
Thanks Mark! So I punched some holes in the decals and applied the warm sugar water, but unfortunately it did not seem to make a noticeable difference. I decided my best shot was to just grab the scalpel and remove the decals, which was very easy. Bogicevic said the solution would get under the decals! I have successfully applied new decals, and my little Italian job is now base-worthy. New pics to come.

Bogicevic Vladimir
Well, you find a solution, which is the most important thing. I can not know why something that worked for me many times does not work for you in this case. Maybe that what I think is silvering is residual glue from decal paper. Who knows... Anyway, good luck with your project.

Doubtingmango
Thanks Bogicevic! You were definitely part of the solution

John
All's well that ends well. 👍 Mango, your builds have me hankering to do some armor but I still have commitments to do a couple more a/c. When I do get a chance, part of me wants to start small with a Pz IV, but another part says go for broke and do a Maus!

gorby
Very nice work!

Neuling
Good result anyway!

Doubtingmango
Thanks guys!

Doubtingmango
As promised, new pics of the new decals have been added, along with pics of the work I have started on the base. Once again, thank you for the help Bogicevic!

John
Really cool base! 👍

Neuling
Good paintwork and weathering, well presented!

S B
Thanks, Neuling. This is so far the most complex and work intensive paintjob and weathering I've done. If you want to see the real jet, this is the link: fighter-wings.com/ai..de-vasylkiv-airbase/

Best regards !!

Neuling
🙂

CaptGPF
Agree with Neuling - absolutely beautiful build! The weathering makes it so photo realistic

Spanjaard
i just love picture 42, what a great job.

Spanjaard
i can not see the images in the link you sent 🙁 the site suggest me to change country to see it 😛

S B
Hey Spanjaard, thank you very much. I have the same problem with the link. Try this one instead: airfighters.com/phot..G-29C-9-13/35-WHITE/

S B
Thank you very much, CaptGPF.

Spanjaard
thanks, that works! 🙂