Yak-130 in progress
Double S-curvature of the intakes (vertical and lateral) is faithfully reproduced along with the turbine blades. I have only filled the front - visible part of the seam.
Lower part of the intakes serves also as the main landing gear wells. While nicely detailed, only little will be seen through small apertures. Unfortunately due to the design of the wheel well doors (most are closed and open only during the transition), m
Although a complex multi-part breakdown of the rear fuselage, the fit is rather good but one mustn't hurry and should check the dryfit before applying any glue.
Upper piece of the intakes attached which also serves as top fuselage and wings support. Although not given an option, one can open up auxiliary intakes and pose the aircraft as with running engines with a little bit of scratchbuilding. Pilot figures are
Lower part of the fuselage. Some seam needing clean up but just a few sweeps with sanding stick will solve those. Biggest problem is the exhaust area which is quite tiny and there are three seams to clean up inside of it.
Full length intakes with fan clearly visible in the depths.
I HATE IT WHEN THIS HAPPENS! I was gonna use Microdesign photo-etch set for this model and luckily checked the parts. PE parts are too big to fit!!!
Rear IP is as bad as front. Seat belts are also too wide.
After a long while, some progress after almost shelving the kit.
Sitting on her wheels all armed up and ready for fight 🙂
A couple of K-36L-3,5Ya 0-0 ejection seats, heavily benefiting from using photoetched parts
评论
16 December 2017, 17:46
Sebastijan Videc
Thanks, guys! Cuajete, it might be strange, but when you start building it, it makes perfect sense. You can actually start with the cockpit as well, but the most work lies in the back fuselage.
Thanks, guys! Cuajete, it might be strange, but when you start building it, it makes perfect sense. You can actually start with the cockpit as well, but the most work lies in the back fuselage.
17 December 2017, 18:40
Bart Goesaert
I'll grab a seat too... very interested in this kit, or maybe the Kitty Hawk one in 1/48, but then I'll wait for a build review...
I'll grab a seat too... very interested in this kit, or maybe the Kitty Hawk one in 1/48, but then I'll wait for a build review...
19 December 2017, 15:52
Bart Goesaert
Bummer with the PE, will you use it as a guide to scratch the pieces?
Bummer with the PE, will you use it as a guide to scratch the pieces?
28 December 2017, 10:13
Burkhard D
Following...seems to be a nice kit in terms of detail. I took some walkaround shots of the Yak-130 in Farnboro last year.
Following...seems to be a nice kit in terms of detail. I took some walkaround shots of the Yak-130 in Farnboro last year.
28 December 2017, 11:48
Sebastijan Videc
Bart - I ordered Eduard PE set as a replacement and will try to scratchbuilt some smaller stuff
Burkhard D - very nice! I first saw it at MAKS airshow near Moscow a few years ago, I don't think a trainer aircraft has ever impressed me so much.
Bart - I ordered Eduard PE set as a replacement and will try to scratchbuilt some smaller stuff
Burkhard D - very nice! I first saw it at MAKS airshow near Moscow a few years ago, I don't think a trainer aircraft has ever impressed me so much.
28 December 2017, 20:22
Daniel Mysak
Nice start, clean work so far. Got two Yaks in my stash too so I´ll keep watching your progress.
Nice start, clean work so far. Got two Yaks in my stash too so I´ll keep watching your progress.
17 January 2018, 08:13
Sebastijan Videc
Indeed, Adam! I'm putting a coat of primer tonight, followed by camo tomorrow if all goes according to plans 🙂
Indeed, Adam! I'm putting a coat of primer tonight, followed by camo tomorrow if all goes according to plans 🙂
23 January 2018, 09:21
Sebastijan Videc
actually 3-tone😉 but yeah, the same as on Su-35S', bottom of Naval Su-30SMs and some new Su-27SM3s
actually 3-tone😉 but yeah, the same as on Su-35S', bottom of Naval Su-30SMs and some new Su-27SM3s
23 January 2018, 12:39
Adam Gudynowski
I've seen it already painted somewhere else. Where are the photos?😉
I've seen it already painted somewhere else. Where are the photos?😉
7 February 2018, 07:52
Sebastijan Videc
thanks, guys! Ronan, I've used Mr.Paint paints. They recently released a set for new camo as seen on Su-35S, Yak-130 and some other aircraft, but only 2 of 3 colours are somewhat correct so I used Blue from Su-33, Light Blue from Su-27/33 and Blue of Su-35S.
thanks, guys! Ronan, I've used Mr.Paint paints. They recently released a set for new camo as seen on Su-35S, Yak-130 and some other aircraft, but only 2 of 3 colours are somewhat correct so I used Blue from Su-33, Light Blue from Su-27/33 and Blue of Su-35S.
11 February 2018, 16:28
Sebastijan Videc
Thanks, guys! Bart, I've seen a couple of photos of Kubinka based Yaks, which were carrying this white mottled drop tanks instead of classic white or grey ones and I thought it would add visual interest to the model.
Thanks, guys! Bart, I've seen a couple of photos of Kubinka based Yaks, which were carrying this white mottled drop tanks instead of classic white or grey ones and I thought it would add visual interest to the model.
21 March 2018, 18:13