USS Bon Homme Richard (CV/CVA-31) Double Build
![Album image #1 Album image #1](/albums/img/9/6/2/833962-48557-27-720.jpg)
![Album image #2 Album image #2](/albums/img/9/6/6/833966-48557-57-720.jpg)
![Album image #3 Album image #3](/albums/img/9/6/7/833967-48557-31-720.jpg)
![Album image #4 Album image #4](/albums/img/9/7/4/833974-48557-64-720.jpg)
![Album image #5 Album image #5](/albums/img/9/7/6/833976-48557-41-720.jpg)
![Album image #6 Album image #6](/albums/img/2/7/8/834278-48557-73-pristine.jpg)
Day 1 - 68 gets hangar and hull blisters.
![Album image #7 Album image #7](/albums/img/9/1/6/834916-48557-79-720.jpg)
Day 2 - 45 gets hull & hangar paint; 68 gets hull blisters worked on.
![Album image #8 Album image #8](/albums/img/9/4/7/835947-48557-51-720.jpg)
One of the features on this build is that the #1 elevator on both will be in the down position, with the elevator well detailed. Here, 45 gets the #1 elevator detailed. The Dragon kit already has accurate elevator walls - they just need detail.
![Album image #9 Album image #9](/albums/img/9/4/8/835948-48557-15-720.jpg)
The transverse piece represents the gallery deck, which is visible when the elevator is in the down position.
![Album image #10 Album image #10](/albums/img/9/4/9/835949-48557-38-720.jpg)
BHR '45 #1 elevator finished (I did go back later with a grayer shade of black for scale effect).
![Album image #11 Album image #11](/albums/img/9/5/0/835950-48557-86-720.jpg)
![Album image #12 Album image #12](/albums/img/9/5/3/835953-48557-38-720.jpg)
![Album image #13 Album image #13](/albums/img/5/1/1/872511-48557-75-720.jpg)
Because I built the hull blister slightly too high on 68 I decided it would be easier to just cut the kit off at the hangar deck, which would also let me control the hangar wall detailing. I built the hangar deck far forward enough to accommodate the #1 elevator well.
![Album image #14 Album image #14](/albums/img/5/1/2/872512-48557-78-720.jpg)
Because the Hasegawa kit now had no landmarks for construction above the main deck at all, I transferred a set of frame marks to graph paper and glued that to the build dock, then made a guide that could be placed over the model to mark the centerline and frame locations as needed.
![Album image #15 Album image #15](/albums/img/5/1/3/872513-48557-12-720.jpg)
![Album image #16 Album image #16](/albums/img/5/1/4/872514-48557-48-720.jpg)
After studying the photos of CV-16's SCB-27C modernization, which involved cutting the forward part of the bow off, I decided to do the same, and cut the kit bow off at frame 5.
![Album image #17 Album image #17](/albums/img/5/1/5/872515-48557-49-720.jpg)
I then used reduced copies of tracings of the plans to add main, 2nd, and forecastle decks up to the frame 1 (FP).
![Album image #18 Album image #18](/albums/img/5/1/6/872516-48557-61-720.jpg)
![Album image #19 Album image #19](/albums/img/5/1/7/872517-48557-72-720.jpg)
![Album image #20 Album image #20](/albums/img/5/1/8/872518-48557-44-720.jpg)
The hangar decks walls were a sheet of .040, with an outer skin of .020 so the openings would not be overly thick. I decided to include a "lip" at the top to serve as a guide for aligning the kit flight deck and eventually the .020 sheet final flight deck.
![Album image #21 Album image #21](/albums/img/5/1/9/872519-48557-88-720.jpg)
I reused the kit's forward "wall" as a guide to align the flight deck.
![Album image #22 Album image #22](/albums/img/5/2/0/872520-48557-61-720.jpg)
The bow was made up of multiple sheets of .040 with .020 spacers at the FP and A-F points, which are marked on the graph paper. This is probably the second one, A.
![Album image #23 Album image #23](/albums/img/5/2/1/872521-48557-83-720.jpg)
Here the forward 5" gallery has been framed up, the escalator from Model Mopnkey added, and the opening for elevator #3 made.
![Album image #24 Album image #24](/albums/img/5/2/2/872522-48557-51-720.jpg)
![Album image #25 Album image #25](/albums/img/5/2/3/872523-48557-72-720.jpg)
This shows the tracing of the plans to provide the necessary templates for construction. The tracings were copied to provide a draker reproduction, then reduced to 27%.
![Album image #26 Album image #26](/albums/img/5/2/4/872524-48557-17-720.jpg)
The #1 elevator well is roughed in.
![Album image #27 Album image #27](/albums/img/5/2/5/872525-48557-74-720.jpg)
The elevator well is complete (except detailing) and the flight deck cut to accommodate it. This photo shows what isn't apparent in photos - that the enlarged elevator was also extended aft.
![Album image #28 Album image #28](/albums/img/5/2/6/872526-48557-67-720.jpg)
A feature of the SCB-27C modernizations is the complete deletion of the "boat deck" on the starboard side aft in favor of a larger hangar deck. This photo shows the -27A Oriskany, the 1945 CV-31, and the -27C CV-31. It's not immediately apparent, but only the blister top is outside the hangar.
![Album image #29 Album image #29](/albums/img/5/2/7/872527-48557-44-720.jpg)
The elevator opening is perfect - except that it's several times too thick, especially with another layer on plastic yet to come on top of it. Time for a new plan.
![Album image #30 Album image #30](/albums/img/5/2/8/872528-48557-67-720.jpg)
![Album image #31 Album image #31](/albums/img/5/2/9/872529-48557-84-720.jpg)
![Album image #32 Album image #32](/albums/img/5/3/0/872530-48557-46-720.jpg)
These are the Model Monkey islands for both ships.
![Album image #33 Album image #33](/albums/img/5/3/1/872531-48557-81-720.jpg)
I chopped a large rectangular hole to allow the elevator to rise up to the existing flight deck level.
![Album image #34 Album image #34](/albums/img/5/3/2/872532-48557-73-720.jpg)
Here it's apparent entire elevator well has been trimmed up .060.
![Album image #35 Album image #35](/albums/img/5/3/3/872533-48557-62-720.jpg)
![Album image #36 Album image #36](/albums/img/5/3/4/872534-48557-31-720.jpg)
![Album image #37 Album image #37](/albums/img/5/3/5/872535-48557-90-720.jpg)
The bow has been built up in layers and the backing for the putty on the sides. The other pieces are the gallery deck undersides, which will be somewhat visible through the elevator openings and door.
![Album image #38 Album image #38](/albums/img/5/3/6/872536-48557-18-720.jpg)
![Album image #39 Album image #39](/albums/img/5/3/7/872537-48557-14-720.jpg)
![Album image #40 Album image #40](/albums/img/5/3/8/872538-48557-77-720.jpg)
The SCB-27C/SCB-125 ships had vertical sides forward and I "plated" those in. The hull curved up smoothly from the waterline and there is no "knuckle" at the forecastle deck as there is in the -27A and -27C ships, so I expected a lot of sanding, so the sides also have wire glued at the knuckle.
![Album image #41 Album image #41](/albums/img/5/3/9/872539-48557-16-720.jpg)
![Album image #42 Album image #42](/albums/img/5/4/0/872540-48557-67-720.jpg)
One very good thing about the Hasegawa kit is that the flight deck has transverse supports underneath, and the catwalks serve as very effective supporting shelves, and I used those as guides to build up the angled deck. From back to front there are .040 supports, with a .020 layer on top to match the catwalks, with another layer of .040 on top to bring it to existing flight deck level. The pencil lines are expansion joints, which I discovered also happen to be where the angles on the added flight deck change.
![Album image #43 Album image #43](/albums/img/5/4/2/872542-48557-55-720.jpg)
![Album image #44 Album image #44](/albums/img/5/4/1/872541-48557-29-720.jpg)
![Album image #45 Album image #45](/albums/img/5/4/3/872543-48557-66-720.jpg)
BHR '45 has to be backdated from the kit, which represents it in 1951-52. Once thing I noticed was that the foremost gun tub - which was added after completion in 1944, was lower. This shows the original tubs and catwalk. The flight deck round-down has already been trimmed back.
![Album image #46 Album image #46](/albums/img/5/4/4/872544-48557-46-720.jpg)
Here the kit catwalks are replaced with thinner .020 strip, the forward tub is lower, and the walkways are in place under the round-down, using Tom's PE.
![Album image #47 Album image #47](/albums/img/5/4/5/872545-48557-46-720.jpg)
68 has the angled deck complete.
![Album image #48 Album image #48](/albums/img/5/4/6/872546-48557-26-720.jpg)
![Album image #49 Album image #49](/albums/img/5/4/7/872547-48557-48-720.jpg)
The modernized Essexes appear to have had their wartime elevators shirted outwards 4-6" to accommodate the blistered hull, hence the white strip. What I was not aware was that the elevators didn't change in dimensions when the ships received angled decks, with the exception of a small round down at the forward end. So I just used the kit elevator.
![Album image #50 Album image #50](/albums/img/5/4/8/872548-48557-25-720.jpg)
The sponsons are in place, and the gallery deck enclosed.
![Album image #51 Album image #51](/albums/img/5/4/9/872549-48557-65-720.jpg)
![Album image #52 Album image #52](/albums/img/5/5/0/872550-48557-46-720.jpg)
This shows the gallery deck being thickened.
![Album image #53 Album image #53](/albums/img/5/5/1/872551-48557-53-720.jpg)
This underside view shows the construction of the sponsons and gallery deck undersides.
![Album image #54 Album image #54](/albums/img/5/5/2/872552-48557-32-720.jpg)
![Album image #55 Album image #55](/albums/img/5/5/3/872553-48557-79-720.jpg)
Started down the port side gallery decks now - note the cutout for the never-mounted gun director has to be filled in.
![Album image #56 Album image #56](/albums/img/5/5/4/872554-48557-34-720.jpg)
![Album image #57 Album image #57](/albums/img/5/5/5/872555-48557-46-720.jpg)
Final 45 port gallery decks - top. Note that the 40mm mounts are all lower than the kit calls for. Many late war Essexes had their mounts lower, likely for weight and stability reasons.
![Album image #58 Album image #58](/albums/img/5/5/6/872556-48557-56-720.jpg)
Final 45 stbd gallery decks - top.
![Album image #59 Album image #59](/albums/img/5/5/7/872557-48557-41-720.jpg)
Final 45 stbd gallery decks - bottom.
![Album image #60 Album image #60](/albums/img/5/5/8/872558-48557-95-720.jpg)
Final 45 port gallery decks - bottom. Note how many places the gallery decks must be built up so that they run into the side of the ship at full thickness.
![Album image #61 Album image #61](/albums/img/5/6/0/872560-48557-32-720.jpg)
![Album image #62 Album image #62](/albums/img/5/6/1/872561-48557-13-720.jpg)
![Album image #63 Album image #63](/albums/img/5/6/2/872562-48557-72-720.jpg)
The final flight deck pieces start to go on. This is the section from the first expansion joint to the second. Note the "lip" is still present to use as a guide.
![Album image #64 Album image #64](/albums/img/5/6/3/872563-48557-85-720.jpg)
I put tubes inside my islands so they can be mounted on a stand and worked on separately from the ship. I also add alignment posts so they can be placed and removed easily until final attachment.
![Album image #65 Album image #65](/albums/img/5/6/4/872564-48557-96-720.jpg)
The final flight deck went on way faster than I had thought.
![Album image #66 Album image #66](/albums/img/5/6/5/872565-48557-45-720.jpg)
![Album image #67 Album image #67](/albums/img/5/6/6/872566-48557-94-720.jpg)
The bow ended up needing some additional sanding to get the proper concave shape at the sides, and in the process I discovered the vertical side forward was too low, so I extracted the wire and carefully sanded the knuckle up. I wire cutwater is visible.
![Album image #68 Album image #68](/albums/img/5/6/7/872567-48557-96-720.jpg)
I scratchbuilt the stern deck structure, but the kit supports were invaluable.
![Album image #69 Album image #69](/albums/img/5/6/9/872569-48557-80-720.jpg)
To my surprise, the structure slid in and out, so I could leave it out until the stern was painted.
![Album image #70 Album image #70](/albums/img/5/6/8/872568-48557-62-720.jpg)
![Album image #71 Album image #71](/albums/img/5/7/0/872570-48557-24-720.jpg)
Just a reminder the 68 in the middle is actually the same kit as 9 in the back.
![Album image #72 Album image #72](/albums/img/5/7/2/872572-48557-25-720.jpg)
![Album image #73 Album image #73](/albums/img/5/7/1/872571-48557-86-720.jpg)
#1 elevator detailed.
![Album image #74 Album image #74](/albums/img/5/7/3/872573-48557-86-720.jpg)
![Album image #75 Album image #75](/albums/img/5/7/4/872574-48557-93-720.jpg)
Finish trimwork for the elevator ended up being a lot simpler than I had expected, and left me with a flight deck opening that, if not exactly as thin as the actual flight deck plating, was think enough that it looked good.
![Album image #76 Album image #76](/albums/img/5/7/5/872575-48557-21-720.jpg)
![Album image #77 Album image #77](/albums/img/5/7/6/872576-48557-53-720.jpg)
Again, the enlarged elevator is substantially longer than it at first appeared.
![Album image #78 Album image #78](/albums/img/5/7/7/872577-48557-17-720.jpg)
![Album image #79 Album image #79](/albums/img/5/7/8/872578-48557-78-720.jpg)
Starting on the pole mast and tractor parking platform.
![Album image #80 Album image #80](/albums/img/5/7/9/872579-48557-11-720.jpg)
An interesting shot of a -27A, a -27A & -125, and a -27C/125 under construction.
![Album image #81 Album image #81](/albums/img/5/8/1/872581-48557-54-720.jpg)
Flight deck marked for detailing.
![Album image #82 Album image #82](/albums/img/5/8/0/872580-48557-21-720.jpg)
I decided to add .05" sheet for the steel landing deck, bomb elevators, and catapults.
![Album image #83 Album image #83](/albums/img/5/8/2/872582-48557-31-720.jpg)
I tried Gunship Gray FS36118 for the flight deck but it seemed too light, so I switched to a Panzer Grey.
![Album image #84 Album image #84](/albums/img/5/8/3/872583-48557-47-720.jpg)
3D printed F6Fs and TBMs are in, and look pretty good after multiple thin coats of glossy Sea Blue.
![Album image #85 Album image #85](/albums/img/5/8/4/872584-48557-14-720.jpg)
First batch of hull detailing.
![Album image #86 Album image #86](/albums/img/5/8/5/872585-48557-43-720.jpg)
Second batch of hull detailing.
![Album image #87 Album image #87](/albums/img/5/8/7/872587-48557-68-720.jpg)
3D printed anchors in. The box contains six, so I have enough to replace the ones on '68 as well.
![Album image #88 Album image #88](/albums/img/5/8/6/872586-48557-16-720.jpg)
The striping is a little wide, so I narrowed it with a brush - here the narrowing is up to the #3 elevator. Note that the centerline of the elevator and the striping is not the same.
![Album image #89 Album image #89](/albums/img/5/9/1/872591-48557-10-720.jpg)
The bow on '68 has the accurate portholes and round-down (give or take). '45 has white deck striping from the Dragon Princeton kit and GMM flight deck numbers that are almost 30 years old.
![Album image #90 Album image #90](/albums/img/5/8/8/872588-48557-65-720.jpg)
45 has striping narrowed. 68 has GMM numerals - fortunately for me she changed from shadowed numbers sometime in '67, so just white in '68. I have started applying other flight deck decals using Starfighter's Nimitz-class carrier set, since they are sold out of the postwar Essex set. The good side of this is that there's twice as much of everything.
![Album image #91 Album image #91](/albums/img/5/8/9/872589-48557-71-720.jpg)
45 gets flight deck structures, and starts getting the flight deck weathered.
![Album image #92 Album image #92](/albums/img/5/9/0/872590-48557-66-720.jpg)
Adding 40mm quads.
![Album image #93 Album image #93](/albums/img/3/7/9/879379-48557-12-720.jpg)
More striping and trim on CVA-31.
![Album image #94 Album image #94](/albums/img/3/8/0/879380-48557-76-720.jpg)
Catwalks port side forward.
![Album image #95 Album image #95](/albums/img/3/8/1/879381-48557-31-720.jpg)
Flight deck decaling complete.
![Album image #96 Album image #96](/albums/img/3/8/2/879382-48557-92-720.jpg)
"Beware" decal up in #1 elevator well.
![Album image #97 Album image #97](/albums/img/3/8/3/879383-48557-87-720.jpg)
Port side aft catwalks.
![Album image #98 Album image #98](/albums/img/3/8/4/879384-48557-38-720.jpg)
Port side forward piping and hatchways,
![Album image #99 Album image #99](/albums/img/3/8/5/879385-48557-93-720.jpg)
Starboard side aft before detailing ...
![Album image #100 Album image #100](/albums/img/3/8/6/879386-48557-61-720.jpg)
... and after detailing.
![Album image #101 Album image #101](/albums/img/4/6/8/880468-48557-21-720.jpg)
Starboard midships detailing.
![Album image #102 Album image #102](/albums/img/4/6/9/880469-48557-92-720.jpg)
![Album image #103 Album image #103](/albums/img/9/0/1/902901-48557-13-720.jpg)
![Album image #104 Album image #104](/albums/img/9/0/2/902902-48557-35-720.jpg)
Portside aft piping and detailing.
![Album image #105 Album image #105](/albums/img/9/0/4/902904-48557-30-720.jpg)
Bridle catcher construction.
![Album image #106 Album image #106](/albums/img/9/0/3/902903-48557-54-720.jpg)
Bridle catchers complete.
![Album image #107 Album image #107](/albums/img/9/0/5/902905-48557-96-720.jpg)
5"/38 caliber mounts by Blue Ridge Models
![Album image #108 Album image #108](/albums/img/9/0/6/902906-48557-48-720.jpg)
![Album image #109 Album image #109](/albums/img/9/0/7/902907-48557-55-720.jpg)
Posts in place to support the main deck railings.
![Album image #110 Album image #110](/albums/img/9/0/8/902908-48557-61-720.jpg)
Starboard forward railings in place.
![Album image #111 Album image #111](/albums/img/9/0/9/902909-48557-42-720.jpg)
#3 elevator structure assembled from a WW II #2 elevator (with some modifications).
![Album image #112 Album image #112](/albums/img/9/1/0/902910-48557-54-720.jpg)
Elevator in place.
![Album image #113 Album image #113](/albums/img/9/1/1/902911-48557-67-720.jpg)
Elevator nets in place.
![Album image #114 Album image #114](/albums/img/9/1/2/902912-48557-13-720.jpg)
![Album image #115 Album image #115](/albums/img/9/1/3/902913-48557-65-720.jpg)
3D printed aircraft from 1968 air group are in.
![Album image #116 Album image #116](/albums/img/9/1/4/902914-48557-62-720.jpg)
Testing out new aircraft.
![Album image #117 Album image #117](/albums/img/9/1/5/902915-48557-59-720.jpg)
Installing the stack grille is just an excuse to put CVA-31 next to CV-34.
![Album image #118 Album image #118](/albums/img/9/1/6/902916-48557-37-720.jpg)
I discovered that the #1 elevator well had been repainted black by 1968, so had to repaint the well.
![Album image #119 Album image #119](/albums/img/9/1/7/902917-48557-28-720.jpg)
On the positive side, some clear photos allowed me to confirm I needed three warning decals.
![Album image #120 Album image #120](/albums/img/9/1/8/902918-48557-82-720.jpg)
CV-31 (and CV-9) get starboard bow 20mms, railings and floater net baskets, and radio antennae.
![Album image #121 Album image #121](/albums/img/9/1/9/902919-48557-62-720.jpg)
Stern gets railing, a closed chock, and nameplate.
![Album image #122 Album image #122](/albums/img/9/2/0/902920-48557-30-720.jpg)
Cleaned the paint off the waterline plate so I can prove yes, this is the Hasegawa kit.
![Album image #123 Album image #123](/albums/img/9/2/1/902921-48557-26-720.jpg)
White border around #1 elevator.
![Album image #124 Album image #124](/albums/img/9/6/6/902966-48557-80-720.jpg)
#2 elevator support structure (and railing) in place.
![Album image #125 Album image #125](/albums/img/9/6/7/902967-48557-23-720.jpg)
CV-31 railings & baskets back to the island.
![Album image #126 Album image #126](/albums/img/9/6/8/902968-48557-66-720.jpg)
Port side aft catwalk railings & baskets in place.
![Album image #127 Album image #127](/albums/img/9/6/9/902969-48557-39-720.jpg)
Port side aft catwalk railings & baskets in place.
![Album image #128 Album image #128](/albums/img/9/7/0/902970-48557-29-720.jpg)
CV-31 railings, 20mms, baskets and antennae complete on port side.
![Album image #129 Album image #129](/albums/img/9/7/2/902972-48557-99-720.jpg)
CVA-31 main deck port side railings complete (with closed chocks).
![Album image #130 Album image #130](/albums/img/1/0/7/955107-48557-18-720.jpg)
![Album image #131 Album image #131](/albums/img/1/0/9/955109-48557-87-720.jpg)
![Album image #132 Album image #132](/albums/img/1/1/0/955110-48557-56-720.jpg)
![Album image #133 Album image #133](/albums/img/1/1/1/955111-48557-74-720.jpg)
![Album image #134 Album image #134](/albums/img/1/1/2/955112-48557-33-720.jpg)
![Album image #135 Album image #135](/albums/img/1/1/3/955113-48557-82-720.jpg)
![Album image #136 Album image #136](/albums/img/1/1/4/955114-48557-30-720.jpg)
![Album image #137 Album image #137](/albums/img/1/1/8/955118-48557-15-720.jpg)
![Album image #138 Album image #138](/albums/img/1/1/5/955115-48557-90-720.jpg)
![Album image #139 Album image #139](/albums/img/0/9/4/955094-48557-11-720.jpg)
![Album image #140 Album image #140](/albums/img/0/9/5/955095-48557-57-720.jpg)
![Album image #141 Album image #141](/albums/img/0/9/3/955093-48557-49-720.jpg)
![Album image #142 Album image #142](/albums/img/0/9/7/955097-48557-59-720.jpg)
![Album image #143 Album image #143](/albums/img/0/9/8/955098-48557-71-720.jpg)
![Album image #144 Album image #144](/albums/img/0/9/9/955099-48557-42-720.jpg)
![Album image #145 Album image #145](/albums/img/1/0/0/955100-48557-70-720.jpg)
![Album image #146 Album image #146](/albums/img/1/0/1/955101-48557-96-720.jpg)
![Album image #147 Album image #147](/albums/img/1/0/2/955102-48557-13-720.jpg)
![Album image #148 Album image #148](/albums/img/1/0/3/955103-48557-42-720.jpg)
![Album image #149 Album image #149](/albums/img/1/0/4/955104-48557-74-720.jpg)
![Album image #150 Album image #150](/albums/img/1/0/5/955105-48557-45-720.jpg)
![Album image #151 Album image #151](/albums/img/1/0/6/955106-48557-71-720.jpg)
![Album image #152 Album image #152](/albums/img/1/0/8/955108-48557-28-720.jpg)
![Album image #153 Album image #153](/albums/img/1/1/6/955116-48557-45-720.jpg)
![Album image #154 Album image #154](/albums/img/1/1/7/955117-48557-91-720.jpg)
![Album image #155 Album image #155](/albums/img/1/1/9/955119-48557-31-720.jpg)
![Album image #156 Album image #156](/albums/img/1/2/0/955120-48557-87-720.jpg)
![Album image #157 Album image #157](/albums/img/1/2/1/955121-48557-60-720.jpg)
![Album image #158 Album image #158](/albums/img/1/2/2/955122-48557-97-720.jpg)
![Album image #159 Album image #159](/albums/img/1/2/3/955123-48557-31-720.jpg)
![Album image #160 Album image #160](/albums/img/1/2/4/955124-48557-38-720.jpg)
![Album image #161 Album image #161](/albums/img/1/2/5/955125-48557-43-720.jpg)
![Album image #162 Album image #162](/albums/img/1/2/6/955126-48557-81-720.jpg)
![Album image #163 Album image #163](/albums/img/1/2/7/955127-48557-96-720.jpg)
![Album image #164 Album image #164](/albums/img/1/2/8/955128-48557-94-720.jpg)
![Album image #165 Album image #165](/albums/img/1/2/9/955129-48557-61-720.jpg)
![Album image #166 Album image #166](/albums/img/1/3/0/955130-48557-80-720.jpg)
![Album image #167 Album image #167](/albums/img/1/3/1/955131-48557-64-720.jpg)
![Album image #168 Album image #168](/albums/img/1/3/2/955132-48557-59-720.jpg)
![Album image #169 Album image #169](/albums/img/1/3/3/955133-48557-54-720.jpg)
![Album image #170 Album image #170](/albums/img/1/3/4/955134-48557-19-720.jpg)
![Album image #171 Album image #171](/albums/img/1/3/5/955135-48557-12-720.jpg)
![Album image #172 Album image #172](/albums/img/1/3/6/955136-48557-68-720.jpg)
![Album image #173 Album image #173](/albums/img/1/3/7/955137-48557-75-720.jpg)
评论
12 29 August 2020, 20:36
Album info
Double build of CV-31 in 1945 and 1968.