SUEZ OURAGAN
1February 28, 2021
2February 28, 2021
3February 28, 2021
4February 28, 2021
5February 28, 2021Beefing up weak legs.
6February 28, 2021
7February 28, 2021
8February 28, 2021Nose wheel strut drilled out, strut then shortened by 2mm.
9February 28, 2021
10March 20, 2021Epoxy plug as cockpit front, doubles as blanking plate behind splitter. Cut off front of cockpit "tub" to allow for dropping in of splitter once interior of intake trunk is smoothed. Test fits going well so far!
11April 9, 2021Got my new Hasegawa Tri-Tool scribing templates!
12April 9, 2021They work quite nicely....
13April 9, 2021Wings scribed, fuselage next....
14April 19, 2021Scribing done, airframe built and primed.
15April 19, 2021Worst fitting part of kit, better test fitting would have saved some time here. Still, a great fit for an old kit. Got some minor scribing to fix, wing tanks are tough to scribe straight!
16April 25, 2021Brush formula (BlueLine ) Hataka paint, lovely stuff!-Two coats of Silk Grey on, belly - bubbles in green circle are caused by not wetting the brush first..easily remedied. Levels nicely, I will be getting more of their products!.
17January 7, 2024Re-shot undersides with Vallejo Model Air USAF light grey 71.296
18January 7, 2024Vallejo Model Air IDF blue 71.113
19January 7, 2024color recommendations for 50s IDF colors all over the place, went with Yoav Efrati's suggested colors, using Vallejo Model Air Golden brown 71.032 and IDF blue 71.113 - now you can see the sizable gap around the windscreen to fill -
20January 7, 2024Tamiya FB thinned for black - Yellow is Vallejo med. yellow with a drop of orange
21January 7, 2024not too shabby, they kinda look hand painted as most marking were applied hastily
22January 7, 2024Fuselage stripes are gonna be tough to keep straight - next thing on the list.
23January 15, 2024Striping done, gear on
24January 15, 2024
25January 15, 2024Marking it as A/C 92 from 113 Squadron, Hornets. (Squadron currently flies AH-64D Sarafs)
26January 15, 2024still have to paint antenna on front of fin. The closed "2" was not common
27January 15, 2024Print Scale decals are nice and thin, behave well so far - the sharkmouth is correct with red on the bottom, as the Heller kit decals have the black and red reversed. May need some help with the curvature of the intake - letting them settle overnight.
28January 21, 2024Done
29January 21, 2024
30January 21, 2024
31January 21, 2024
32January 21, 2024Print Scale decals still silvered a wee bit - maybe base was not glossy enough? Small aerial on left of nose is made from fur off of my German Shepherd - once segmented, the thick kt canopy will fit right over the rear decking. Pitot tube is steel music wire.
评论
已禁用
Album info
Reinforce all gear legs, removed front of cockpit tub to allow intake splitter to be dropped in after inside seams smooth, separate one lump canopy, rescribe all raised panel lines,(!) thin all gear doors, fill in HUGE tail separation canyon and rescribe that, remove 2mm from nose gear strut after rod is inserted, proper Sharkmouth decals with black and red in right places, open gun tubes.
32 图片
1:72
已完成
Dassault MD 450B Ouragan
Heyl Ha'Avir (Israeli Air Force 1948-now)113 Tayeset (Hornet) Sqn. 27
十月 1956 Suez Crisis
Blue, Brown, Light grey