E-5015A
Ready for the primer
The - 1st color is airbrushed: rust tones
Base color is airbrushed
Masking again....
Unmasked!
Waiting to activate the chipping fluid.....
Worn effects done
Details painted
Pinwash done
It's completed!
Körös Makett Kupa 2023 - Békéscsaba (HU) - 2nd place
Wolfpack Makett Kup - Zalaegerszeg (HU) - Silver Medal
Bolyai Makettépítő Kupa - Budapest (HU) - Silver Medal
Nitra Model 2023 - Nitra (SK) - Awarded Model
New Year Cup 2024 - Beograd (RS) - Maketarski Klub Novosadski Ikar Special Award
Slovak Open 2024 - Rimavská Sobota (SK) - Awarded Model
Mosonshow 2024 - Mosonmagyaróvár (HU) - Silver Medal
Novosadski Ikar Kup 2024 - Novi Sad (RS) - 2nd place
PSMK Cup - Budapest (HU) - 5th place
Trofeul AMA - Alba Iulia (RO) - 2nd place
EastModels Challenge 2024 - Liptovsky Hrádok (SK) - Awarded model
EastModels Challenge 2024 - Liptovsky Hrádok (SK) - Panzershow Special Award
评论
157 14 June 2023, 18:20
Zsolt CzegleThank you mates!
It's a fast project again for a Facebook Group build event Vörös Június ( Red June) between 12.6 and 12.7. The main rule: build a Soviet or Russian manufactured vehicle/pláne. So I decided to build this little excavator...
16 June 2023, 14:29
Zsolt CzegleThank you mates for your interest!
Meanwhile I attached some lead wires as "hydraulic tubes" there are still some pieces to glue and I can start with the most interesting part: the painting
18 June 2023, 21:48
Shar DipreeLooks extremely nice and full of details. I'm looking forward to the end result.
29 June 2023, 20:28
Zsolt CzegleThank you Shar. I hope I can paint it and do the base chipping today. 🙂
30 June 2023, 10:33
Zsolt CzegleThe little excavator got his colors. Now he is waiting to be chipped...
30 June 2023, 20:51
Michael KohlYeah, that's the way it is suppose to look. The only slight issue I have are the hydraulic hoses. They look a bit too kinky. Being made frome rubber I would expect them to have a smoother routing. Probably something that can still be fixed.
16 July 2023, 18:45
Zsolt CzegleThank you Michael for your remark. After checking the reference photos I realized that the hydraulic tubes are shorter than I made, so I'll replace them! Maybe I'll replace them with coper wire instead of lead wires so they won't be so kinky.
17 July 2023, 05:40
Michael KohlFor my D9 build I used silicone tubes. They route nicely but attract dust like anything. So copper wire would be my choice too.
17 July 2023, 10:03
Zsolt Czegle"Hydraulic tubes" are removed. 😉
I painted additional dirt and grime effects with oilpaints.
19 July 2023, 19:43
Edgars BizūnsAmazing work, love the weathering all around! Also very finely produced model kit, lot to clean up?
21 July 2023, 05:10
Zsolt CzegleThank you Edgars! It's still ca. 90% completed.
The kit 3D printed so the casted resin parts had some visible layering but not that bad, so I could remove them with some sanding. The casting qualiti is perfect, there was almost nothing to clean. Fitting the parts was also without any problems.
21 July 2023, 07:30
Zsolt CzegleThe building phase is done. Weathering process is also completed. Now I have to complete the base and the figure.
23 July 2023, 18:20
Simon NagorsnikOh Wow!!
It's always a pleasure watching your work!
Perfect paint job, outstanding as always 👏👏
27 July 2023, 14:17
gorbyCongratulations Zsolt. I assume that award means something a lot more impressive than 'OK level'. It's certainly a vast amount better than just 'OK'. 😉
6 September 2023, 17:02
bughunterAll the prices have a bigger volume than the model itself 😉
Congratulation for each and all of your medals! 👍
23 April, 10:49
Simon NagorsnikYou can't do much better than this - excellent performance!
Congratulations and here's to a successful next time!
24 April, 17:26
