时间线
Wall
Qwertzel
添加了一个新相册
添加了一个新相册
8 7 June, 15:25
John
Cool! I was wondering how all the extra parts in mine looked when done, very nice. 👍
If you will accept a bit of advice, when you complete the cabin "shell" that goes into the fuselage halves, be prepared to do a lot of trimming and fitting before closing up. On mine, the sides of the fuselage wanted to push the roof of the cabin down and also hit the edges of the windscreen opening and that left a big gap on top. I finally got it acceptable fit, but even then, I wish I had cut more away because the cabin roof does not quite fit flush.
Cool! I was wondering how all the extra parts in mine looked when done, very nice. 👍
If you will accept a bit of advice, when you complete the cabin "shell" that goes into the fuselage halves, be prepared to do a lot of trimming and fitting before closing up. On mine, the sides of the fuselage wanted to push the roof of the cabin down and also hit the edges of the windscreen opening and that left a big gap on top. I finally got it acceptable fit, but even then, I wish I had cut more away because the cabin roof does not quite fit flush.
20 June, 15:34
Qwertzel
Thanks for the advice. I'll take care of it 🙂
I build a lot of Revell kits in the past and the fitting was different with every model. I have got everything between pretty good and horrible. It's always like a mysterious box.
Thanks for the advice. I'll take care of it 🙂
I build a lot of Revell kits in the past and the fitting was different with every model. I have got everything between pretty good and horrible. It's always like a mysterious box.
20 June, 16:28
John
I'm sure you will do well with all that Revell experience. 👍 The good news is that other than the cabin shell, the rest fits OK (ish) even the windscreens. But if you want doors closed, also be prepared to do some surgery on them.
I'm sure you will do well with all that Revell experience. 👍 The good news is that other than the cabin shell, the rest fits OK (ish) even the windscreens. But if you want doors closed, also be prepared to do some surgery on them.
20 June, 17:35
July 10, 2024
Qwertzel
添加了一个新相册
添加了一个新相册
13 4 April, 16:38
DerSchottologe
I see you've left the license plate holder on. I should have done the same! I tried to remove it as requested in the instructions by "sanding it off" but my result isn't very good. The whole rear side looks a bit rough now haha.
I see you've left the license plate holder on. I should have done the same! I tried to remove it as requested in the instructions by "sanding it off" but my result isn't very good. The whole rear side looks a bit rough now haha.
10 July, 22:07
June 26, 2024
June 23, 2024
June 22, 2024
June 21, 2024
June 20, 2024
June 7, 2024
June 4, 2024
May 30, 2024
Qwertzel
想要这件
想要这件
5t Pallet Truck & Wooden Pallet with 200 Litre Oil Drum and Plastic Barrel
Gecko Models 1:35
35GM0034 2023 新模具 多主题 (3)30 May, 11:36
May 27, 2024
May 20, 2024
May 18, 2024
May 17, 2024
May 15, 2024
May 14, 2024
Qwertzel
想要这件
想要这件
.010 inch (0.30mm) Clear Styrene Sheet 3 x Clear Styrene Sheets (175x300x0.30mm)
Plastruct
91201 (SSM-101) 14 May, 09:10
May 13, 2024
May 12, 2024
May 9, 2024
May 8, 2024
May 5, 2024
Qwertzel
想要这件
想要这件
German Construction Truck to use Italeri Mercedes Benz Actros MP4
A&N Model Trucks 1:24
ANMT-68 2018 新模具 5 May, 18:07
Qwertzel
想要这件
想要这件
Mercedes Sprinter Third Generation
German panel van, 5.5 ton, normalA&N Model Trucks 1:24
ANMT-111 2020 新模具 5 May, 18:06
May 4, 2024
May 3, 2024
April 30, 2024
April 27, 2024
wnolder.php?lang=zh
2024-04-27 13:41:34
2024-01-02 14:56:05
137072
/ajax/wnolder.php?lang=zh&sd=2024-04-27 13:41:34&md=2024-01-02 14:56:05&filter=&w=137072
todo