Zimmerit Coating Sheet for 1/35 Scale Elefant
Tamiya
Tamiya | No 12644 | 1:35
Факти
- Марка:
- Tamiya
- Наименование:
- Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
- Номер:
- 12644
- Мащаб:
- 1:35
- Тип:
- Набор за детайлиране
- В продажба:
- 2012
- Баркод:
- 4950344126446 (EAN)
- Опаковка:
- Опакован в плик
- Тема:
- Sd.Kfz. 184 Ferdinand » Противотанкови самоходки (Превозни средства)
Съдържание на кутията
Лепящ се декал
Размери:
330x135x1 mm
(13x5.3x0 inch)
Тегло:
20 g (0.04 lbs)
Предназначен за
Афтърмаркета е предназначен за:
Tamiya
2012
Нова матрицаИнструкции
Изтегли 2605Kb (.pdf)
Пазар
Онлайн магазини
USD 6.99
В наличност »
USD 8.80
В наличност »
USD 9.35
В наличност »
USD 10.50
В наличност »
USD 10.62
В наличност »
USD 11.00
В наличност »Покажи всички оферти » (16 общо)
Алтернативни SKU за Tamiya 12644:
74-T12644 | 300012644 | HC_12644 | T12644 | TAM-12644 | TAM12644
Забележка: Цените и наличността са индикативни. Проверете дали продуктът действително съвпада!
Преглед на съдържанието
Външни прегледи
Реклама
Преглед
AMPS
Преглед
IPMS USA
Проекти
Коментари
Jens AndréeI have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
4 July 2017, 01:13
Holger KranichHi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
4 July 2017, 06:35
Jens AndréeI badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
4 July 2017, 20:25
Материал за справка
Всички книги » (14 общо) Всички walkarounds » (3 общо)