Airbus A400M "ATLAS"

Revell | No. 04859 | 1:144

Okosságok

Márka:: Revell
Cím:: Airbus A400M "ATLAS"
Szám:: 04859 (Más néven 80-4859)
Méretarány:: 1:144
Típus:: Teljes készlet
Megjelent:: 2014 Új eszköz
Vonalkód:: 4009803048598 (EAN)
Csomagolás:: Összecsukható doboz (oldalra nyiló)
Téma:: Airbus A400M Atlas » Propelleres (Repülőgép)

Jelölések

Airbus A400M Atlas

Airbus A400M Grizzly

Airbus (1970-now)

F-WWMZ
2013

Airbus A400M-180 Atlas

Bundeswehr Luftwaffe (German Air Force 1956-now)

LTG 62 54+01
2014 - Wunstorf

Armée de l'Air (French Air Force 1934-2019)

F-RBAB "Ville de Toulouse"
2014

A doboz tartalma

Műanyag rugó (Clear), Műanyag rugó (Light gray), Matrica (nedves) (Multi-colored), Utasítások (papír) (Black & white)

Méretek:
537x207x63 mm (21.1x8.1x2.5 inch)

Boxart tervezte Andrzej Deredos

Mi van a dobozban »

Termék idővonal

Revell

2014

2024

Új eszköz

Készlet

Teljes előtörténet »

Útmutató

Letöltés 6326Kb (.pdf)

Piactér

Online boltok

zł 95.40

USD 24.77Nincs raktáron »

Magánkereskedelem és csere

EUR 45.00

Kapcsolatfelvétel az eladóval

Alternatív cikkszámok a következőhöz Revell 04859:
RVL04859

Jegyzet: Az árak és a rendelkezésre állás csak tájékoztató jellegűek. Ellenőrizd a termék tényleges eggyezőségét is.

Kapcsolódó termékek

Detailing set for aircraft model Airbus A400M

Metallic Details 1:144

MD14422 2019 Új eszköz

RMAF Airbus A400M Anniversary Decals Limited Edition

MiniatureWorld Models 1:144

MWMD020 2019 Új eszköz

painting mask

Airbus A400M “Atlas" for Revell

KV Models 1:144

14301

painting mask

Airbus A400 for Revell

KV Models 1:144

14600-1

Airbus A400M Atlas

Babibi model 1:144

DDT-01021 (BBB01021) 2017 Új eszköz

Minden kapcsolódó termék » (10 összesen)

In-box értékelés

Külső vélemények

Hirdetés

Dobozon belüli áttekintés

IPMS Deutschland

Dobozon belüli áttekintés

Modellversium

Dobozon belüli áttekintés

Hyperscale

Felülvizsgálat

FineScale Modeler Forum

Minden értékelés » (7 összesen)

Magazinok

Sky Model | 80

Italian (TOC: 11 lines)

December-January 2015

Model Airplane International | 162

English (TOC: 19 lines)

January 2019

Model Airplane International | 115

English (TOC: 9 lines)

February 2015

Összes magazin » (7 összesen)

Hozzászólások

Treehugger
Suggestions for other builders:
1) Consider doing something with the stabilizers/elevators, which connects to the tail, but actually has this flat surface. This flat surface is molded onto the tail, which doesn't look the best, it should be connected to the stabilizers/elevators.
2) Decal sheet has some obvious errors. Also the yellow prop warning on the hull is supposed to be angled to be parallel with the tilted engines for anyone in doubt.
3) I used a nose weight of 30g iirc, at the nose and around the cabin area at the front, the manual suggests 40g. Note: I had the loading ramp closed.
4) Try make sure you get all the four engines tilted properly, so don't sand off too much plastic here and there.
5) The decal sheet have dark grey "A400M" decals on it. It would be important to make the paint lighter than the darker decals. I couldn't figure out if the decals were too light in color or not compared to photos.

1 March 2020, 21:03

Dave Flitton
Interesting information, thanks

1 March 2020, 23:00

Treehugger
Also, I found out that, one can't glue on the wheels, if you already glued on all the other parts for the landing gear and also all the aircraft hull parts.

What would work, is gluing on the wheels + the next big part and put those two things into the landing gear bay.

Once can ofc glue it all together, but that would make painting the wheels tricky, unless you want to put masking tape all over each wheel, which seems tedious.

2 March 2020, 09:54

Florian H.
thx for the info 🙂

2 March 2020, 12:20

5 November 2024, 01:25 -

Treehugger
Better watch out for those sink marks. Make sure you add some putty around all the windows and sand down before starting to add any primer. :|

I think my brain somehow ingnored them, maybe because my brain went "that can't be sink marks, not around all the windows, that would be silly, really around all the windows?". Or "I am already busy with those other sink marks over here, I will have to ignore this."

9 February 2020, 09:42

wilky
Having worked in a plastic injection molding factory that's a result of not enough pressure in the shot.
Obviously the machine operator hasn't informed the die setter of the issue.
Poor quality control
Total lack of care about the finished product

9 February 2020, 09:55

Treehugger
The issue seems to be where the plastic hull is at its thickest, because on the inside, more plastic is protruding. Would be nice to know if this is preventable, or not. It sounds like maybe it is preventable, by being more careful working with the injection mold machine (or maybe in the configuration of it).

The sink marks around all the windows aren't deep, but just enough deep to annoy.

9 February 2020, 10:16

wilky
It'd be the pressure of the shot.
Low pressure means not enough material is in the mold space.
Plastic cools and shrinks. This is why it's happening where it's thicker.
Hopefully it was detected during the run and not all kits are the same

9 February 2020, 10:42

Treehugger
Looking at the kit again I should correct myself. Six of ten windows have noticeable sink marks. I've already added primer and some color, but I think I will just bite it and sand off the paint and add the putty. :|

Thanks for the feedback. 🙂

9 February 2020, 12:39