Zimmerit Coating Sheet for 1/35 Scale Elefant

Tamiya

Tamiya | No. 12644 | 1:35

概要

メーカー:: Tamiya
タイトル:: Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
品番:: 12644
縮尺:: 1:35
タイプ:: 詳細セット
発売日:: 2012
バーコード:: 4950344126446 (EAN)
包装:: 袋詰め
トピック:: Sd.Kfz. 184 Ferdinand » 駆逐戦車 (乗り物)

中身

デカール（ステッカー）

寸法:
330x135x1 mm (13x5.3x0 inch)

重量:
20 g (0.04 lbs)

想定品

このセットの想定商品:

Tamiya

2012

新金型

説明書

ダウンロード 2605Kb (.pdf)

市場

オンラインショップ

すべてのオファーを表示 » (16 合計)

の代替 SKU Tamiya 12644:
74-T12644 | 300012644 | HC_12644 | T12644 | TAM-12644 | TAM12644

注意: 価格と在庫状況はあくまで目安です。製品が実際に一致するかどうかも確認してください。

インボックスレビュー

外部レビュー

レビュー

AMPS

レビュー

IPMS USA

レビュー

review.rcecho.com

プロジェクト

38 画像

Sd.kfz.184 "Elefant"

1:35

プロジェクト: Sd.kfz.184 "Elefant"

1:35 Zimmerit Coating Sheet for 1/35 Scale Elefant (Tamiya 12644)

9 画像

Sd.Kfz. 184 Schwerer Jagdpanzer "Elefant"

1:35

Sd.Kfz. 184 Schwerer Jagdpanzer "Elefant"

プロジェクト: Sd.Kfz. 184 Schwerer Jagdpanzer "Elefant"

1:35 8.8cm Pak 43/1 L/71 Ferdinand & Elefant (RB Model 35B86)

101 画像

Sd.Kfz. 184 Schwerer Jagdpanzer Elefant

1:35

プロジェクト: Elefant

1:35 Tool Box for Brummbar, Ferdinand, or Elefant (Aber 35A118)

1:35 SdKfz 184 "Elefant" (Eureka XXL ER-3527)

10 画像

Sd.Kfz.184 Schwerer Jagdpanzer "Elefant"

1:35

プロジェクト: Sd.Kfz.184 Schwerer Jagdpanzer "Elefant"

1:35 Elefant Tiger P (H) VK 45.01/45.02 (Friulmodel ATL-23)

Jens Andrée
I have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.

4 July 2017, 01:13

Holger Kranich
Hi Jens,

i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger

4 July 2017, 06:35

Jens Andrée
I badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!

4 July 2017, 20:25