Zimmerit Coating Sheet for 1/35 Scale Elefant
Tamiya
Tamiya | Nr. 12644 | 1:35
Fakty
- Marka/Wydawnictwo:
- Tamiya
- Tytuł:
- Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
- Numer:
- 12644
- Skala:
- 1:35
- Rodzaj:
- Zestaw waloryzacji
- Wydane:
- 2012
- kod kreskowy:
- 4950344126446 (EAN)
- Opakowanie:
- W woreczku
- Temat:
- Sd.Kfz. 184 Ferdinand » Niszczyciele czołgów (Pojazdy)
Zawartość pudełka
Nalepka/Naklejka
Wymiary:
330x135x1 mm
(13x5.3x0 inch)
Waga:
20 g (0.04 lbs)
Zaprojektowany do
Ten zestaw akcesoriów przeznaczony jest do:
Tamiya
2012
Nowe formyInstrukcje
Pobierz 2605Kb (.pdf)
Giełda
Sklepy internetowe
USD 6.99
Na stanie »
USD 8.80
Na stanie »
USD 9.35
Na stanie »
USD 10.50
Na stanie »
USD 11.00
Na stanie »
USD 12.49
Na stanie »Pokaż wszystkie oferty » (17 razem)
Alternatywne jednostki SKU dla Tamiya 12644:
74-T12644 | 4950344126446 | 300012644 | HC_12644 | T12644 | TM 12644
Uwaga: Ceny i dostępność są tylko wskazówkami. Sprawdź dokładnie, czy produkt rzeczywiście pasuje!
Recenzja zawartości
Recenzje zewnętrzne
Reklama
Przejrzeć
AMPS
Przejrzeć
IPMS USA
Projekty
9 zdjęć/zdjęcia
Sd.Kfz. 184 Schwerer Jagdpanzer "Elefant"
1:35
Sd.Kfz. 184 Schwerer Jagdpanzer "Elefant"
Komentarzy
Jens AndréeI have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
4 July 2017, 01:13
Holger KranichHi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
4 July 2017, 06:35
Jens AndréeI badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
4 July 2017, 20:25
Materiał referencyjny
Wszystkie książki » (14 razem) Wszystkie walkaroundy » (3 razem)