CURTISS CONDOR ANTARCTIC EXPEDITION FLOATPLANE
![Album image #1 Album image #1](/albums/img/9/6/8/1712968-64707-99-720.jpg)
very old....so old the molds were "rediscovered" in 1988.....reissued by Glencoe and originally an ITC (Ideal Toy Co) piece....these models have been in the stash forever and always intimidated because of the age and rigging....
![Album image #2 Album image #2](/albums/img/9/6/9/1712969-64707-28-720.jpg)
...rough and needing a lot of attention....but, this is not an attempt for modeling perfection so this is entirely a lark....
![Album image #3 Album image #3](/albums/img/9/6/7/1712967-64707-76-720.jpg)
![Album image #4 Album image #4](/albums/img/9/0/9/1712909-64707-82-720.jpg)
note the later instructions have float position wrong....
![Album image #5 Album image #5](/albums/img/9/7/0/1712970-64707-45-720.jpg)
....not a bad fit....
![Album image #6 Album image #6](/albums/img/6/4/0/1713640-64707-46-720.jpg)
....not many pieces to paint but that ORANGE and that BLUE need to stand out and a full bottle of both has been allocated....NO PAINT will be applied to the totally cool retro modeling deco art clear molded stand...worth the price of admission of you tackle one of these kits (they are out there for sale)
Note....yes, this stand means a big gash in the bottom of the aircraft....didn't worry much about the bottom of this one....
....the fuselage was already glued up so an interior was out of the question....
Note....yes, this stand means a big gash in the bottom of the aircraft....didn't worry much about the bottom of this one....
....the fuselage was already glued up so an interior was out of the question....
![Album image #7 Album image #7](/albums/img/6/6/6/1713666-64707-86-720.jpg)
...this AIMS wire set for a 1/32 SE.5 has a great selection of dual rigging wires with good connections already created...holes are drilled into the engines where the dual wires go...the single wires are excellent as well and will be used everywhere they can...not worried about the connections UNDER wings so only the bottoms need to have a good look...
![Album image #8 Album image #8](/albums/img/0/0/9/1717009-64707-96-720.jpg)
...critical ORANGE may have been reached.....at least three coats maybe four.....for some reason, the top wing looks more color saturated here but to the unaided eye, its almost the opposite....
![Album image #9 Album image #9](/albums/img/1/3/9/1717139-64707-93-720.jpg)
...back and forth with whether the horizontal stabilizers should be blue or orange...this settled it...clearly orange....
![Album image #10 Album image #10](/albums/img/4/8/5/1720485-64707-65-720.jpg)
...the roughest part of this old kit is the cockpit window....its not much use to try the kit windows so they got filled in....the attempt will be to make a decal and cover the window area....that can be tough because a light color is needed and decals aren't great printed at home with light colors....the outline of the decal is seen here as a piece of tape laid across a kit window and then trimmed and removed...it will be the template for the decal....
![Album image #11 Album image #11](/albums/img/5/1/5/1720515-64707-71-720.jpg)
...in the end, it was silver painted tape with blacklines added....perfection in modeling?... hardly...but this project was never about that....happy with this result...decals are next....
![Album image #12 Album image #12](/albums/img/7/0/7/1722707-64707-57-720.jpg)
...old decals but they laid down well......the condor is getting close....
![Album image #13 Album image #13](/albums/img/7/2/3/1724723-64707-50-720.jpg)
....the tail is rigged and the first float attached....it will sit for 24 hours to let the glue set....
![Album image #14 Album image #14](/albums/img/8/8/6/1724886-64707-17-720.jpg)
a great drawing made in 1965....it shows detail of connections....one thing clearly shown is the fuel tank install in the top wing and the spouts and vents for that....none of that is molded on to the top wing of this old kit...some wires will be used to at least nod in that direction...photos show a variety of vent pipes and who knows what special connections were made for this Antarctic voyage......
![Album image #15 Album image #15](/albums/img/5/9/2/1727592-64707-62-720.jpg)
...floats attached and struts to be installed on float two....the first strut turned out a bit askew and no photos will be taken to emphasize this effect....in addition, no expense was spared to create these two wright cyclone engine replicas......strictly OOB
![Album image #16 Album image #16](/albums/img/3/1/2/1729312-64707-77-720.jpg)
...in a complete jig operator error moment...all the center supports for the wings got pulled from their glued spots on the tops of the engines...its a mess....and the wing will have to come off and some kind of "repair" done with thin styrene to cover it up...ouch....
![Album image #17 Album image #17](/albums/img/3/9/8/1729398-64707-74-720.jpg)
....trying to recover with a little help with wires in the struts and some bezels on the "mounts" to add texture, along with some riveting...
![Album image #18 Album image #18](/albums/img/4/1/6/1729416-64707-74-720.jpg)
....back to work....in the end, it actually looks better than stock so it was all worth it...
![Album image #19 Album image #19](/albums/img/4/0/2/1730402-64707-58-720.jpg)
...one side "rigged"....the double wires will be attached on the bottom of the top wing once it is finally installed....
![Album image #20 Album image #20](/albums/img/9/1/1/1732911-64707-78-720.jpg)
...all "rigged" up.....fuel "vents" added to the top wing.....floats rigged....wing control horns and line....still to do...antenna...front mounted landing lights....engines....
![Album image #21 Album image #21](/albums/img/6/2/2/1735622-64707-25-720.jpg)
Engines, Forward landing lights, Antenna and cool Art Deco stand complete....very close now....
![Album image #22 Album image #22](/albums/img/3/1/2/1736312-64707-55-720.jpg)
....all done with this orange and blue flying boat (or is it a floatplane?)...the jaunty flying angle is a result of the stand...not sure if they meant for this to be the look but it works....photos are next....
Comentarii
26 22 April, 01:05
![](/profiles/img/64707-255-s.jpg)
...off this goes....note the instructions for the 1954 older ITC model have the float position correct. Several other modelers looked into this and explicitly said the correct position is in the instructions for the ITC kit and, by golly, they match up to the pin holes in the wing...pretty easy decision....
download the ITC instructions here...
Curtiss CONDOR (ITC 3724, 1:81)
23 April, 03:39
![](/profiles/img/104687-298-s.jpg)
rare plan, rarely see something like that. It already looks really interesting and I'm very excited to see what happens next. good luck!
24 April, 06:36
![](/profiles/img/64707-255-s.jpg)
welcome to this old time adventure plane kit from the dawn of modeling, designed to visit Antarctica...there is also a skied version
27 April, 04:01
![](/profiles/img/14143-361-s.jpg)
You get a medal for the courage to build this kit. And a second medal for the result.🙂
7 May, 03:38
![](/profiles/img/130395-735-s.jpg)
I just love seeing these old kits getting built. Better than leaving them up in a closet festering away. Looking forward to seeing this completed.
9 May, 00:56
![](/profiles/img/64707-255-s.jpg)
...in a complete jig operator error moment...all the center supports for the wings got pulled from their glued spots on the tops of the engines...its a mess....and the wing will have to come off and some kind of "repair" done with thin styrene to cover it up...ouch....
13 May, 19:57
Album info
....VERY OLD KIT (1954!) BUT A COOL AIRPLANE...THE LARGEST OF ITS TIME....