Zimmerit Coating Sheet for 1/35 Scale Elefant
Tamiya
Tamiya | No. 12644 | 1:35
Чињенице
- Бренд:
- Tamiya
- Наслов:
- Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
- Број:
- 12644
- Размера:
- 1:35
- Тип:
- Сет детаља
- Издато:
- 2012
- Бар код:
- 4950344126446 (EAN)
- Паковање:
- У кеси
- Тематика:
- Sd.Kfz. 184 Ferdinand » Разарачи тенкова (Возила)
Садржај кутије
Децалсхеет (налепнице)
Величине:
330x135x1 mm
(13x5.3x0 inch)
Тежина:
20 g (0.04 lbs)
Дизајниран за
Овај афтермаркет сет је дизајниран за:
Tamiya
2012
Нови алатУпутства
Преузимање 2605Kb (.pdf)
Тржиште
Интернет продавнице
USD 6.99
На лагеру »
USD 8.80
На лагеру »
USD 9.35
На лагеру »
USD 10.50
На лагеру »
USD 10.62
На лагеру »
USD 11.00
На лагеру »Прикажи све понуде » (16 укупно)
Алтернативни СКУ-ови за Tamiya 12644:
74-T12644 | 300012644 | HC_12644 | T12644 | TAM-12644 | TAM12644
Белешка: Цене и доступност су само информационог типа. Такође проверити да ли се производ подудара!
In-box рецензије
Екстерне рецензије
Реклама
Преглед
AMPS
Преглед
IPMS USA
Пројекти
10 слике
Sd.Kfz.184 Schwerer Jagdpanzer "Elefant" 
1:35
Пројекат: Sd.Kfz.184 Schwerer Jagdpanzer "Elefant"
Коментари
Jens AndréeI have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
4 July 2017, 01:13
Holger KranichHi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
4 July 2017, 06:35
Jens AndréeI badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
4 July 2017, 20:25
Референтни материјал
Све књиге » (14 укупно) Сви унаоколни прегледи » (3 укупно)