Zimmerit Coating Sheet for 1/35 Scale Elefant
Tamiya
Tamiya | No. 12644 | 1:35
Gerçekler
- Marka:
- Tamiya
- Başlık:
- Zimmerit Coating Sheet for 1/35 Scale Elefant Tamiya
- Numara:
- 12644
- ölçek:
- 1:35
- tip:
- Detay seti
- Yayınlandı:
- 2012
- Barkod:
- 4950344126446 (EAN)
- paketleme:
- torbalı
- konu:
- Sd.Kfz. 184 Ferdinand » Tank avcıları (Araçlar)
Kutu içeriği
Çıkartma (çıkartmalar)
boyutlar:
330x135x1 mm
(13x5.3x0 inch)
Ağırlık:
20 g (0.04 lbs)
İçin tasarlandı
Bu satış sonrası seti için tasarlanmıştır:
Tamiya
2012
Yeni araçTalimatlar
İndir 2605Kb (.pdf)
Pazaryeri
Çevrimiçi mağazalar
USD 6.99
Stokta var »
USD 8.80
Stokta var »
USD 9.35
Stokta var »
USD 10.50
Stokta var »
USD 10.62
Stokta var »
USD 11.00
Stokta var »Tüm teklifleri göster » (16 toplamda)
için alternatif SKU'lar Tamiya 12644:
74-T12644 | 300012644 | HC_12644 | T12644 | TAM-12644 | TAM12644
Not: Fiyatlar ve uygunluk sadece göstergedir. Ürünün gerçekten aynı olup olmadığını da kontrol edin!
Kutu içi incelemeler
Dış incelemeler
reklâm
gözden geçirmek
AMPS
gözden geçirmek
IPMS USA
Projeler
Yorumlar
Jens AndréeI have mixed feelings about this zimmerit sheet. The quality was great! No doubt about it - BUT there's no excuse to not cutting the pieces with a laser cutter or knife plotter my Tamiya. Cutting out the pieces wasn't too hard, but all the little holes that needed cutting was a different story... I eventually resorted to using small PCB drills to cut the holes needed, but perfect it wasn't and unless Tamiya starts to pre-cut the individual pieces I won't do another zimmerit sheet. Just my opinion.
4 July 2017, 01:13
Holger KranichHi Jens,
i have this sheet too and i am not very amused, too. And i experienced that in corners or edges the glue dont stick enough. And for the holes, you have to take a punch and die set.
BTW welcome to scalemates!
Cheers Holger
4 July 2017, 06:35
Jens AndréeI badly wanted a punch set when I discovered that you had to cut all those holes in the sheet, but they are sadly missing from my otherwise extensive "toolbox", but brand new PCB drills did the trick - but it was slow and required more than a few breaks in order to "cool down"...
I've been lucky so far with my zimmerit still sticking well to the model, but I made sure not to touch the sticky side prior to placing them and I hope it'll work in the long run? I'd be a bit upset if they start to peel off in a year or so... Regardless, unless Tamiya pre-cuts these zimmerit sheets I won't ever use them again. Not fully thought through if you ask me - but they look fantastic when done!
Thanks for you kind comment!
4 July 2017, 20:25
Referans malzemesi
Bütün kitaplar » (14 toplamda) Tüm geziler » (3 toplamda)