Gloster Gladiator Mk.I/Mk.II/J-8
Meteo Reconnaissance & Foreign Service
Roden | 货号： 438 | 1:48
基本信息
- 品牌:
- Roden
- 标题:
- Gloster Gladiator Mk.I/Mk.II/J-8 Meteo Reconnaissance & Foreign Service
- 数量:
- 438
- 比例:
- 1:48
- 类型:
- 完整套件
- 发布:
- 2004 新贴花
- 条码:
- 4823017700888 (EAN)
- 主题:
- Gloster Gladiator » 螺旋桨 (飞机)
水贴
Gloster Gladiator
Gloster Gladiator J-8A
Svenska Flygvapnet (Swedish Air Force 1926-now)
- F8 8/5
1941 World War 2
Silver
Gloster Gladiator Mk.I
Wehrmacht Luftwaffe (German Air Force 1935-1945)
- Erpr.Gr. 1 NJ+B
1942 World War 2
Dark Slate grey
Militair Vliegwezen-Aéronautique Militaire (Belgian Air Force 1925-1940)
- 1 Esc. Comet, I Groupe, 2 Rég. d'Aéro G-30
1938 Pre World War 2
Silver, US Light Green
Lietuvos Karinės Oro Pajėgos (Lithuanian Air Force 1919-40 & 1992-now)
- 5 Eskadrile G-704
1938 Pre World War 2
Silver, Dark Green
Latvijas Gaisa Spēki (Latvian Air Force 1918-40 & 1992-now)
- 175
1937 Pre World War 2
Pale Blue, US Light Gree
Hærens flyvåpen (Norwegian Army Air Service 1914-1944)
- Black 427 (Sgt. F. F. Schye)
四月 1940 World War 2 - Fornebu
Silver
Военно-воздушные силы СССР (Soviet Air Forces 1918-1992)
- G-709
1941 World War 2 - Baltic Coast
Gloster Gladiator Mk.II
Royal Air Force (1918-now)
- 1401 (Met) N2309/B
1942 World War 2 - Bircham Newton
Dark Green, Light grey, Ocean grey - 1402 (Met) N5592
一月 1945 World War 2 - Aldergrove
Dark Earth, Dark Green, Beige Green
开盒详情
注塑口 (Clear), 注塑口, 水贴
产品时间线
全部历史 »
新模具
新零件
新零件
新贴花
新贴花
新零件说明书
下载 6936Kb (.pdf)
市场
网店
USD 18.99
有货 »
USD 24.50
有货 »
USD 26.24
可用 »
€ 19.75
USD 22.68有货 »
€ 21.72
USD 24.95有货 »
€ 23.95
USD 27.51有货 »显示所有报价 » (9 总计)
私下交易和交换
替代 SKU Roden 438:
ROD438 | PKROD438 | RN438
注: 价格与有货情况均仅供参考。也请留意产品是否与查物匹配！
相关产品
Gloster Gladiator Mk.I late & Mk.II Instrument Panel (for Roden/Eduard)
Yahu Models 1:48
YMA4832 2015 新模具 
Gloster Gladiator Mk.I Over Belgium Recommended for Eduard, Merit, Roden Kit.
LF Models 1:48
C48154 2017 新模具 
所有相关产品 » (65 总计)
开盒测评
外部链接评测
广告
开盒测评
Modellversium
链接已经损坏
Internet Modeler
杂志
项目
相册
所有主题 » (22 总计)
评论
Justin ThomasI appreciate this kit being available, the engine detail, instructions, only a little flashing, the decal options, variants and separate ailerons, elevators and rudder. But I personally found it to be a difficult kit. The fitting of the engine in the cowl is difficult. I had to trim parts of the engine. Assembly of the cockpit into the joining halves of the fuselage is fiddly. Fitting the top wing on the six struts is difficult. There are minuscule holes on the wings/fuselage for the minuscule studs on the base of the struts. It would have been a lot easier and stronger if the struts had fit into cavities the size of the base of the strut. The engine gets stuck on the front a bit haphazardly. The struts have to be very carefully removed from the sprue to avoid damaging them. So expect some awkwardness.
1 5 March 2019, 12:05
参考资料
