scalare baze de date de modelare | manager de rezervă

Soviet SU-100Y Self-Propelled Gun

Trumpeter | No. 09589 | 1:35

Boxart SU-100Y Self-Propelled Gun 09589 Trumpeter

Fapte

Marca:
Trumpeter
Titlu:
Soviet SU-100Y Self-Propelled Gun
Număr:
09589
Scară:
1:35
Tip:
Kit complet
Eliberată:
2021 Instrumentul nou
Cod de bare:
9580208095899 (EAN)
ambalare:
Casetă rigidă (deschizător de vârf)
Subiect:
T-100 » Rezervoare (vehicule)

Conținutul cutiei

Dimensiuni:
410x260x78 mm (16.1x10.2x3.1 inch)

Greutate:
647 g (1.43 lbs)

Cronologie produs

 
Trumpeter
Istorie completă »

Piata de desfacere

Magazine online
Logo Squadron Hobbies
USD 60.74
USIn stoc »
Logo Super-Hobby.com
USD 71.31
PLIn stoc »
Logo Hobbylinc.com
USD 75.69
USIn stoc »
Logo MegaHobby.com
USD 79.01
USIn stoc »
Logo Sprue Brothers Models
USD 89.49
USIn stoc »
Logo 1001hobbies.com
USD 60.83
FRDisponibil »

Afișați toate ofertele » (14 in total)

SKU-uri alternative pentru Trumpeter 09589:
TRU09589 | TR09589 | U09589 | TRUM09589 | PKTM09589 | TR 09589

Notă: Prețurile și disponibilitatea sunt numai indicații. De asemenea, verificați dacă produsul se potrivește cu adevărat!

Produse asemanatoare

35L-339
130mm Soviet B-13 barrel for SU-100Y SPG
Aber 1:35
35L-339 2023 Instrumentul nou

In-box recenzii

Recenzii externe

Nu știm despre niciun comentariu în cutie pentru acest lucru SU-100Y Self-Propelled Gun (#09589) din Trumpeter.

proiecte

27 imagini
Su-100Y SPG 1:35 TrumpeterView album, image #1
1:35
1:35 SU-100Y Self-Propelled Gun (Trumpeter 09589)

Comentarii

Ron Garcia
Not a "paper panzer" as the Soviets did make one example so I decided it build this tank. This is very large tank but a quick build due to minimal details and no turret. The minimal details comment is not a criticism. I guess the original tank's exterior was spartan and so it is on this one.

I had four track links left over with a slight sag so you will pretty much be using all of them. Cutting them all out and cleaning up the attachment points takes longer than putting them together. If you leave the drive sprocket and idler wheel loose, you can remove the tracks for painting and reinstalling.

The front periscope was the only thing that gave me a bit of trouble. The directions show gluing in part GP1-2 first before D6. I would reverse that. D6 has a frame around the top that goes over the periscope. With GP1-2 in place beforehand, there's no way to get the frame around the periscope and securing it to the upper hull. The holes for D6 are also too small so I had to widen them to get the part to fit. The directions do say to install D6 first but that's on the second drawing so it's not immediately clear they are talking about the entire step 4. I didn't realize this and it caused me problems so be careful. Also, the covering, part D7, doesn't quite go low enough over the periscope in my opinion. If you install it into the notches, the covering leaves the top of the periscope exposed. I modified mine so it sat closer to part GP1-2.

When attaching the cable end to part E3, the only way to do so is to cut one side of part D15 so you can spread it open like a clasp and then attach it over the bar in the middle of part E3. That being the case, it would probably be easier to cement part E3 in place and attach the cable afterwards. I super glued E3 on after I painted the tank and cable. It was a little awkward with the cable attached to it.

Other than that, this was a trouble free build. The gun even elevates (I've had trouble with this on other recent builds). It looks good sitting on my shelf next to my SMK and T-100 tanks. Recommended if you want an easy build of a very large and obscure early WWII Soviet tank.
2 5 July 2022, 18:29